The main body ECU (multiplex network body ECU) controls the rear fog light.
Inspect the fuse for circuits related to this system before performing the following procedure.
w/ Entry and Start System:
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Fog Light Relay | Rear fog lights | OFF or ON | Light control switch in Tail or Head position. |
Rear fog lights turn on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (except 5L-E) | B |
| NG (for 5L-E) | C |
A
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>PROBLEM SYMPTOMS TABLE
B
C
Disconnect the 2Q*1, 2P*2 and 2K driver side junction block assembly connectors.
*1: for LHD
*2: for RHD
Disconnect the V3 rear fog light assembly LH connector.
Disconnect the U3 rear fog light assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2K-1 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2Q-11 - V3-1 | Always | Below 1 Ω |
| 2Q-11 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2P-11 - V3-1 | Always | Below 1 Ω |
| 2P-11 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *A | for LHD | *B | for RHD |
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2Q-11 - Battery negative (-) terminal | Battery not connected to 2K-1, A-14 (TRLY) and A-27 (RFGO) | Below 1 V |
| Battery positive (+) → 2K-11
Battery negative (-) → A-14 (TRLY) and A-27 (RFGO) |
11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2P-11 - Battery negative (-) terminal | Battery not connected to 2K-1, A-14 (TRLY) and A-27 (RFGO) | Below 1 V |
| Battery positive (+) → 2K-11
Battery negative (-) → A-14 (TRLY) and A-27 (RFGO) |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear fog light relay (FOG RR) from engine room relay block.
Inspect the rear fog light relay (FOG RR).
Click hereVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear fog light relay (FOG RR) from engine room relay block.
Disconnect the V3 rear fog light assembly LH connector.
Disconnect the U3 rear fog light assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Rear fog light relay (FOG RR) terminal 2 - Body ground | Light control switch in Tail or Head position. | 11 to 14 V |
| Rear fog light relay (FOG RR) terminal 5 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Rear fog light relay (FOG RR) terminal 3 - V3-1 | Always | Below 1 Ω |
| Rear fog light relay (FOG RR) terminal 3 or V3-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear fog light relay (FOG RR) from engine room relay block.
Disconnect the 2F driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Rear fog light relay (FOG RR) terminal 1 - 2F-19 | Always | Below 1 Ω |
| Rear fog light relay (FOG RR) terminal 1 or 2F-19 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2F-19 - A-27 (RFGO) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG