Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › RELAY › from 2017.08
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260444 RELAY G

5L-E ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 28300 1.INSPECT STARTER RELAY (ST)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 28610 2.INSPECT GLOW PLUG RELAY (GLOW)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 82641 3.INSPECT NO. 1 INTEGRATION RELAY (IG2)

A406471C01
1.333,2.167 1.667,2.417 0.333,0.25 3,2.167 3.333,2.417 0.333,0.25 5,2.167 5.333,2.417 0.333,0.25 0.115,0.115 0.563,0.469 0.448,0.354 10 false *a 1.406,2.208 1.885,2.531 0.479,0.323 10 false 1C 3.073,2.219 3.552,2.542 0.479,0.323 10 false 1B 5.073,2.219 5.552,2.542 0.479,0.323 10 false 1A
*a Component without harness connected
(No. 1 Integration Relay)
- -


NOTICE:
·

The IG2 relay and EFI relay are built into the No. 1 integration relay.

·

Before performing the relay inspections for the relays of the No. 1 integration relay, inspect the IG2 and EFI fuses.



a.

Inspect the IG2 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1A-5 Battery voltage not applied to terminals 1A-2 and 1A-1 10 kΩ or higher
Battery voltage applied to terminals 1A-2 and 1A-1 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



b.

Inspect the EFI relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage not applied to terminals 1B-3 and 1B-2 10 kΩ or higher
Battery voltage applied to terminals 1B-3 and 1B-2 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



Hide 4.INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

U115459C02
0.771,0.792 1.188,1.083 0.417,0.292 10 false 2K 2.75,0.792 3.167,1.083 0.417,0.292 10 false 2D 5.427,0.792 5.844,1.083 0.417,0.292 10 false 2A 0.115,0.104 0.583,0.427 0.469,0.323 10 false *a
*a Component without harness connected
(Main Body ECU)
- -


NOTICE:
·

The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).

·

Before performing the relay inspections for the relays of the main body ECU (driver side junction block), inspect the ACC and IG1 fuses.



a.

Inspect the ACC relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-17 - 2K-1 Battery voltage not applied to terminals 2A-48 and 2D-4 10 kΩ or higher
Battery voltage applied to terminals 2A-48 and 2D-4 Below 1 Ω


If the result is not as specified, replace the main body ECU.



b.

Inspect the IG1 NO. 1 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-33 - 2K-1 Battery voltage not applied to terminals 2A-52 and 2D-4 10 kΩ or higher
Battery voltage applied to terminals 2A-52 and 2D-4 Below 1 Ω


If the result is not as specified, replace the main body ECU.