Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2017.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM C

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P279E  Four Wheel Drive (4WD) Range Signal Circuit Range / Performance  


DESCRIPTION

When the transfer position switch is switched, the HI terminal and LO terminal change to one of the following ON/OFF combinations listed in the table below.

Transfer Position Switch Terminal H4F Between H4F and H4L H4L Between H4L and L4L L4L
HI ON OFF ON OFF OFF
LO OFF OFF ON OFF ON

This DTC is detected if the transfer position switch HI terminal and LO terminal signals are simultaneously received.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P163B
1.

Ignition switch turned to ON

2.

The ON/OFF combination of the HI terminal and LO terminal does not match the pattern

3.

60 seconds or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer position switch



WIRING DIAGRAM

C325754E12
0.917,2.156 2.521,2.344 1.604,0.188 10 false Transfer Position Switch 0.917,1.979 1.375,2.177 0.458,0.198 10 false G18 2.833,0.802 3.292,1 0.458,0.198 10 false HI 2.865,1.427 3.177,1.625 0.313,0.198 10 false LO 3.146,0.802 3.302,1 0.156,0.198 10 false 5 3.135,1.438 3.292,1.635 0.156,0.198 10 false 2 1.479,0.927 1.885,1.104 0.406,0.177 10 false H4F 2.073,1.125 2.385,1.323 0.313,0.198 10 false H4L 1.563,1.521 1.875,1.719 0.313,0.198 10 false L4L 1,1.115 1.458,1.313 0.458,0.198 10 false GND 0.802,1.115 0.958,1.313 0.156,0.198 10 false 4 5.063,0.771 5.375,0.969 0.313,0.198 10 false 14 5.333,0.792 5.792,0.99 0.458,0.198 10 false 2-4 5.063,1.417 5.375,1.615 0.313,0.198 10 false 13 5.344,1.406 5.656,1.604 0.313,0.198 10 false LO 5.052,2.198 6.76,2.406 1.708,0.208 10 false 4 Wheel Drive Control ECU 5.063,2.031 5.521,2.229 0.458,0.198 10 false G53 5.854,0.24 6.167,0.438 0.313,0.198 10 false IG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER POSITION SWITCH)
a.

Disconnect the G53 4 wheel drive control ECU connector.


b.

Disconnect the G18 transfer position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-14 (2-4) - G18-5 (HI) Always Below 1 Ω
G53-13 (LO) - G18-2 (LO) Always Below 1 Ω
G18-4 (GND) - Body ground Always Below 1 Ω
G53-14 (2-4) or G18-5 (HI) - Body ground Always 10 kΩ or higher
G53-13 (LO) or G18-2 (LO) - Body ground Always 10 kΩ or higher
G53-14 (2-4) or G18-5 (HI) - G53-13 (LO) or G18-2 (LO) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TRANSFER POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TRANSFER POSITION SWITCH
a.
C388082C01
0.594,1.271 0.948,1.51 0.354,0.24 1.417,1.802 0.854,2.448 true 1.854,1.813 2.594,2.406 true 0.625,1.292 1.083,1.49 0.458,0.198 10 false G18 0.771,2.49 1.083,2.688 0.313,0.198 10 false HI 2.656,2.417 2.969,2.615 0.313,0.198 10 false LO
*a Component with harness connected
(Transfer Position Switch)


Remove the transfer position switch with its connector still connected.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-5 (HI) - Body ground Ignition switch ON
H4F position
Below 1.5 V
Ignition switch ON
H4L position
Below 1.5 V
Ignition switch ON
L4L position
10.5 to 14 V
G18-2 (LO) - Body ground Ignition switch ON
H4F position
10.5 to 14 V
Ignition switch ON
H4L position
Below 1.5 V
Ignition switch ON
L4L position
Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG