Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443

All of the following conditions (a) are met (1 trip detection logic)

(a)

The target control value and actual control value do not match for 10 seconds or more.

(b)

The target control value and actual control value do not match for 80 times or more.



·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



CONFIRMATION DRIVING PATTERN

A179391E01
1.525,1.949 1.755,2.124 0.230,0.174 10 [A] 2.846,1.949 3.076,2.124 0.230,0.174 10 [B] 3.892,3.005 4.122,3.179 0.230,0.174 10 [C] 4.574,1.338 4.804,1.512 0.230,0.174 10 [D] 5.097,3.005 5.327,3.179 0.230,0.174 10 [E] 0.509,2.071 0.887,2.255 0.378,0.184 10 Idling 4.224,2.524 5.010,2.837 0.786,0.313 10 10 minutes or more 2.594,2.524 3.380,2.837 0.786,0.313 10 15 minutes or more 1.31,2.524 2.105,2.689 0.795,0.165 10 Warming up 1.38,1.057 3.406,1.380 2.026,0.323 10 Between 40 km/h and 60 km/h (25 mph and 38 mph) 0.954,1.546 1.171,1.139 1.171,1.139 1.269,1.139 false 0.128,0.45 1.081,0.616 0.952,0.165 10 Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C and all accessory switches should be off.


7.

Idle the engine for 15 minutes or more [B].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0443.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



13.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 38 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


WIRING DIAGRAM

A413207E05
5.531,0.406 5.99,0.604 0.458,0.198 10 false PRG 5.146,0.427 5.604,0.625 0.458,0.198 10 false C154 5.26,0.25 5.573,0.448 0.313,0.198 10 false 13 2.698,0.74 3.313,0.938 0.615,0.198 10 false C15 2.708,0.885 4.083,1.083 1.375,0.198 10 false Purge VSV 2.531,0.313 2.688,0.51 0.156,0.198 10 false 2 3.354,0.302 3.51,0.5 0.156,0.198 10 false 1 1.26,0.573 2.635,0.771 1.375,0.198 10 false EFI NO. 2 0.813,2.49 1.885,2.688 1.073,0.198 10 false Battery 1.271,1.833 1.844,2.021 0.573,0.188 10 false 70A FL 2.635,1.688 2.948,1.885 0.313,0.198 10 false 1S 2.646,1.5 2.802,1.698 0.156,0.198 10 false 1 3.438,2.365 4.49,2.594 1.052,0.229 10 false EFI MAIN NO. 1 2.635,2.031 2.948,2.229 0.313,0.198 10 false 1W 2.656,1.875 2.813,2.073 0.156,0.198 10 false 4 2.927,1.781 3.583,2.115 0.656,0.333 10 false EFI MAIN NO. 1 4.385,1.688 4.698,1.885 0.313,0.198 10 false 1W 4.458,1.521 4.771,1.719 0.313,0.198 10 false 10 4.406,2.042 4.719,2.24 0.313,0.198 10 false 1W 4.5,1.875 4.656,2.073 0.156,0.198 10 false 8 5.135,2.031 5.594,2.229 0.458,0.198 10 false G181 5.271,1.854 5.583,2.052 0.313,0.198 10 false 6 5.531,1.938 6.146,2.135 0.615,0.198 10 false MREL 3.313,2.823 6.833,3.021 3.521,0.198 10 false No. 1 Integration Relay 5.969,3 6.427,3.198 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A349021

Connect the GTS to the DLC3.


b.

Disconnect the vacuum hose (charcoal canister side) from the purge VSV.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


f.

Place your finger on port (charcoal canister side). Check if the disconnected port applies suction to your finger when operating the purge VSV using the GTS.

OK:
Tester Operation Specified Condition
VSV ON Purge VSV port applies suction to finger
VSV OFF Purge VSV port applies no suction to finger




OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

OK

3.INSPECT PURGE VSV (POWER SOURCE)

NG

3.INSPECT PURGE VSV (POWER SOURCE)
a.
U169469E03
0.083,0 0.26,0.156 0.177,0.156 10 false *a 0.438,1.083 0.802,1.24 0.365,0.156 10 false C15

Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C15-2 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Purge VSV)



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C15-1 - C154-13 (PRG) Always Below 1 Ω
C15-1 or C154-13 (PRG) - Body ground Always 10 kΩ or higher




OK

5.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


g.

Idle the engine for 15 minutes or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTC: P0443.


j.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P0443 is output) B

HINT:

If the judgment result shows INCOMPLETE or N/A, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 38 mph) for 10 minutes and check the DTC judgment result again.




A

B