Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is OFF when the ST1- signal is OFF.
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A413216E01
6.083,0.458 6.542,0.656 0.458,0.198 10 false STP 6.094,0.896 6.708,1.094 0.615,0.198 10 false ST1- 5.646,0.365 6.26,0.563 0.615,0.198 10 false G180 5.646,0.792 6.26,0.99 0.615,0.198 10 false G180 5.75,0.125 6.063,0.323 0.313,0.198 10 false 10 5.76,0.583 6.073,0.781 0.313,0.198 10 false 11 4.417,1.385 4.875,1.583 0.458,0.198 10 false A99 4.406,1.573 5.594,1.76 1.188,0.188 10 false Stop Light Switch 4.865,0.375 5.021,0.573 0.156,0.198 10 false L 4.865,0.823 5.021,1.021 0.156,0.198 10 false L 4.531,0.354 4.688,0.552 0.156,0.198 10 false B 4.542,0.802 4.698,1 0.156,0.198 10 false B 4.521,1.104 4.979,1.302 0.458,0.198 10 false GND 2.542,0.51 3.156,0.708 0.615,0.198 10 false STOP 1.406,0.521 1.865,0.719 0.458,0.198 10 false ALT 0.385,1.125 0.76,1.531 0.375,0.406 10 false 250A FL 1.25,2.354 2.167,2.552 0.917,0.198 10 false 70A FL 2.031,2.24 2.344,2.438 0.313,0.198 10 false 1S 2.063,2.052 2.219,2.25 0.156,0.198 10 false 1 3.615,2.813 4.073,3.01 0.458,0.198 10 false IG2 2.917,0.948 3.375,1.146 0.458,0.198 10 false IGN 4.094,1.948 4.406,2.146 0.313,0.198 10 false 1V 4.385,1.969 4.542,2.167 0.156,0.198 10 false 1 6.219,2.604 6.833,2.802 0.615,0.198 10 false IG1D 6.01,2.469 6.167,2.667 0.156,0.198 10 false 3 5.927,3.094 6.542,3.292 0.615,0.198 10 false G213 5.948,3.292 7.063,3.875 1.115,0.583 10 false Certification ECU (Smart Key ECU Assembly) 5.698,2.479 6.01,2.677 0.313,0.198 10 false *2 5.677,3.042 5.99,3.24 0.313,0.198 10 false *1 4.771,3.813 6.146,4.01 1.375,0.198 10 false IG2 NO. 2 4.135,3.51 4.292,3.708 0.156,0.198 10 false 6 2.979,3.49 3.135,3.688 0.156,0.198 10 false 7 3.833,3.51 4.292,3.708 0.458,0.198 10 false IG2 3.198,3.49 3.656,3.688 0.458,0.198 10 false AM2 3.125,3.927 3.438,4.125 0.313,0.198 10 false G2 3.125,4.125 7.104,4.323 3.979,0.198 10 false Ignition Switch Assembly*1 4.333,2.615 4.646,2.813 0.313,0.198 10 false 1V 4.385,2.406 4.542,2.604 0.156,0.198 10 false 2 2.021,2.604 2.333,2.802 0.313,0.198 10 false 1W 2.073,2.427 2.229,2.625 0.156,0.198 10 false 4 3.208,3.042 4.688,3.281 1.479,0.24 10 false No. 1 Integration Relay 2.177,3.76 2.49,3.958 0.313,0.198 10 false ST 0.5,4.094 1.573,4.292 1.073,0.198 10 false Battery 1.01,4.063 3.073,4.302 2.063,0.24 10 false *1: w/o Entry and Start System 1.052,4.354 5.49,4.552 4.438,0.198 10 false *2: w/ Entry and Start System 6.229,1.885 6.688,2.083 0.458,0.198 10 false ECM 4.292,0.229 4.448,0.427 0.156,0.198 10 false 7 4.281,0.646 4.438,0.844 0.156,0.198 10 false 6 4.292,0.979 4.448,1.177 0.156,0.198 10 false 2 5.073,0.24 5.229,0.438 0.156,0.198 10 false 3 5.094,0.667 5.25,0.865 0.156,0.198 10 false 5 2.771,2.396 3.229,2.594 0.458,0.198 10 false IG2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
E270270E11
0.26,1.042 0.646,1.333 0.385,0.292 2.698,1.75 2.365,1.219 true 2.063,1.219 1.719,1.844 true 0.323,1.115 0.635,1.313 0.313,0.198 10 false A99 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 2.719,1.781 3.031,1.979 0.313,0.198 10 false B 1.677,1.865 1.833,2.063 0.156,0.198 10 false B

a.

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-7 (B) - Body ground Always 11 to 14 V
A99-6 (B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO.1 INTEGRATION RELAY, BATTERY)

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω



OK

3.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (STP AND ST1- VOLTAGE)
U169556E02
5.844,1.021 6.198,1.458 false 5.813,1.031 5.552,1.448 false 1.073,1.333 1.365,1.552 0.292,0.219 10 false *a 2.885,1.406 3.146,1.573 0.26,0.167 10 false *b 6.229,0.396 6.656,0.563 0.427,0.167 10 false G180 5.271,1.479 5.885,1.667 0.615,0.188 10 false 11(ST1-) 6,1.479 6.646,1.667 0.646,0.188 10 false 10(STP) 4.729,0.125 4.948,0.313 0.219,0.188 10 false *c

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G180-11 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed Below 1.5 V
G181-10 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 11 to 14 V


Text in Illustration
*a Depressed
*b Released
*c Rear view of wire harness connector
(to ECM)



OK

NG

4.CHECK HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH)
4.CHECK HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A99-3 (L) - G180-10 (STP) Always Below 1 Ω
A99-5 (L) - G180-11 (ST1-) Always Below 1 Ω
A99-3 (L) or G180-10 (STP) - Body ground Always 10 kΩ or higher
A99-5 (L) or G181-11 (ST1- ) - Body ground Always 10 kΩ or higher



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR