Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU receives a reverse shift position signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

E280619E28
5.417,0.979 5.833,1.167 0.417,0.188 10 false RL 4.115,0.979 4.375,1.167 0.26,0.188 10 false RL 4.406,0.865 4.667,1.052 0.26,0.188 10 false 1 5.177,0.844 5.438,1.031 0.26,0.188 10 false 27 3.26,0.865 3.521,1.052 0.26,0.188 10 false 2 3.427,0.979 3.688,1.167 0.26,0.188 10 false RB 1.865,1.115 2.813,1.302 0.948,0.188 10 false ECU-IG NO.1 3.177,1.479 4.115,1.667 0.938,0.188 10 false C159 3.177,1.646 4.563,1.99 1.385,0.344 10 false Park/Neutral Position Switch Assembly 5.198,1.604 6.135,1.792 0.938,0.188 10 false I9*1, G228*2 5.198,1.781 6.708,2.125 1.51,0.344 10 false Clearance Warning ECU 0.073,2.167 1.781,2.313 1.708,0.146 10 false *1: for 4 Sensor Type 0.073,2.458 1.781,2.604 1.708,0.146 10 false *2: for 8 Sensor Type 0.156,0.969 1.542,1.156 1.385,0.188 10 false from IG NO.1 Relay 0.146,0.094 2.552,0.406 2.406,0.313 12 false for Automatic Transmission:

E280619E29
5.417,0.979 5.833,1.167 0.417,0.188 10 false RL 4.406,0.865 4.948,1.052 0.542,0.188 10 false 1*3, 2*4 5.167,0.865 5.427,1.052 0.26,0.188 10 false 27 1.865,1.115 2.813,1.302 0.948,0.188 10 false ECU-IG NO.1 2.927,1.49 3.865,1.677 0.938,0.188 10 false C41*3, C160*4 2.927,1.646 5.26,2 2.333,0.354 10 false Back-up Light Switch Assembly 5.198,1.604 6.135,1.792 0.938,0.188 10 false I9*1, G228*2 5.198,1.781 6.708,2.125 1.51,0.344 10 false Clearance Warning ECU 0.104,2.135 1.813,2.281 1.708,0.146 10 false *1: for 4 Sensor Type 0.104,2.427 1.813,2.573 1.708,0.146 10 false *2: for 8 Sensor Type 0.156,0.969 1.542,1.156 1.385,0.188 10 false from IG NO.1 Relay 0.052,0.052 2.458,0.365 2.406,0.313 12 false for Manual Transmission: 2.844,0.854 3.385,1.042 0.542,0.188 10 false 2*3, 1*4 1.656,2.135 3.677,2.313 2.021,0.177 10 false *3: for 1GR-FE, 2TR-FE, 5L-E 1.667,2.417 3.688,2.594 2.021,0.177 10 false *4: for 1KD-FTV, 1GD-FTV

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CLEARANCE WARNING ECU
a.
E309541E03
1.042,0.271 1.396,0.5 0.354,0.229 1.854,0.26 2.24,0.5 0.385,0.24 1.823,1.677 1.448,1.177 true 1.156,0.313 1.469,0.51 0.313,0.198 10 false I9 1.875,0.302 2.354,0.51 0.479,0.208 10 false G228 1.438,0.323 1.75,0.521 0.313,0.198 10 false *A 2.292,0.323 2.604,0.521 0.313,0.198 10 false *B 1.865,1.646 2.177,1.844 0.313,0.198 10 false RL

Disconnect the clearance warning ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I9-27 (RL) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V
I9-27 (RL) - Body ground Ignition switch ON
Shift lever in any position except R
Below 1 V

for 8 Sensor Type
Tester Connection Condition Specified Condition
G228-27 (RL) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V
G228-27 (RL) - Body ground Ignition switch ON
Shift lever in any position except R
Below 1 V


Text in Illustration
*A for 4 Sensor Type
*B for 8 Sensor Type
*a Front view of wire harness connector
(to Clearance Warning ECU)

Result
Result Proceed to
OK A
NG (for Automatic Transmission) B
NG (for Manual Transmission) C



A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

4.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

b.

Inspect the park/neutral position switch assembly.


Result
Result Proceed to
OK A
NG (for AC60F) B
NG (for A750F) C



A

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU AND BATTERY)

B

C

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU AND BATTERY)
a.

Disconnect the C159 park/neutral position switch assembly connector.


b.

Disconnect the I9*1 or G228*2 clearance warning ECU connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-2 (RB) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I9-27 (RL) - C159-1 (RL) Always Below 1 Ω
I9-27 (RL) - Body ground Always 10 kΩ or higher

for 8 Sensor Type
Tester Connection Condition Specified Condition
G228-27 (RL) - C159-1 (RL) Always Below 1 Ω
G228-27 (RL) - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

A

5.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU AND BATTERY)

B

C

D

5.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU AND BATTERY)
a.

Disconnect the C41*1 or C160*2 back-up light switch assembly connector.

*1: for 1GR-FE, 2TR-FE, 5L-E

*2: for 1KD-FTV, 1GD-FTV


b.

Disconnect the I9*1 or G228*2 clearance warning ECU connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1GR-FE, 2TR-FE, 5L-E
Tester Connection Switch Condition Specified Condition
C41-2 - Body ground Ignition switch ON 11 to 14 V

for 1KD-FTV, 1GD-FTV
Tester Connection Switch Condition Specified Condition
C160-1 - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type (for 1GR-FE, 2TR-FE, 5L-E)
Tester Connection Condition Specified Condition
I9-27 (RL) - C41-1 Always Below 1 Ω
I9-27 (RL) - Body ground Always 10 kΩ or higher

for 4 Sensor Type (for for 1KD-FTV, 1GD-FTV)
Tester Connection Condition Specified Condition
I9-27 (RL) - C160-2 Always Below 1 Ω
I9-27 (RL) - Body ground Always 10 kΩ or higher

for 8 Sensor Type (for 1GR-FE, 2TR-FE, 5L-E)
Tester Connection Condition Specified Condition
G228-27 (RL) - C41-1 Always Below 1 Ω
G228-27 (RL) - Body ground Always 10 kΩ or higher

for 8 Sensor Type (for for 1KD-FTV, 1GD-FTV)
Tester Connection Condition Specified Condition
G228-27 (RL) - C160-2 Always Below 1 Ω
G228-27 (RL) - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR