In this circuit, the meter CPU receives engine speed signals from the ECM. The meter CPU displays the engine speed calculated based on the data received from the ECM.
Check if a CAN communication DTC is output.
w/ Central Gatway ECU (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).
w/o Central Gatway ECU (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| CAN communication DTC is not output. | A |
| CAN communication DTC is output. (w/ Central Gatway ECU) | B |
| CAN communication DTC is output. (w/o Central Gatway ECU) | C |
A
B
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>PRECAUTION)
C
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>PRECAUTION)
Using the GTS, perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Tacho Meter Operation | Tachometer | OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000* (rpm) | - |
*: for 1GR-FE, 2TR-FE
Tachometer indication is normal.
| Result | Proceed to |
|---|---|
| CAN communication DTC is not output. | A |
| CAN communication DTC is output. (w/ Central Gatway ECU) | B |
| CAN communication DTC is output. (w/o Central Gatway ECU) | C |
A
B
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>PRECAUTION)
C
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>PRECAUTION)
Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Engine Rpm | Engine speed/Min.: 0 rpm, Max.: 12750 rpm | 600 to 700 rpm (When idling) | If the data received from the ECM exceeds the range that can be displayed on the meter, the meter continues to display the maximum value of the range. |
Engine speed displayed on the intelligent tester is almost the same as the tachometer indication.
Record the engine speed displayed on the intelligent tester.
Check the engine speed when the engine is fully warmed up and the air conditioning and all electrical accessories are off.
OK
NG
Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Engine Speed | Engine speed/Min.: 0 rpm, Max.: 16383 rpm | 600 to 700 rpm (When idling) | - |
Engine speed displayed on GTS is almost same as actual engine speed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Gasoline Engine) | B |
| NG (for Diesel Engine) | C |
for 1GR-FE:
If it is necessary to refer to the SFI system, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 2TR-FE:
If it is necessary to refer to the SFI system, refer to the following procedures (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1KD-FTV:
If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1GD-FTV:
If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1GD-FTV (w/ Urea SCR System):
If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING).
for 5L-E:
If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
A
B
for 1GR-FE: (See pageEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
for 2TR-FE: (See pageEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
C
for 1KD-FTV: (See pageEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
for 1GD-FTV: (See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
for 1GD-FTV (w/ Urea SCR System): (See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING)
for 5L-E: (See pageEngine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Replace the ECM with a new or normally functioning one.
for 1GR-FE: See pageEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 2TR-FE: See pageEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1KD-FTV: See pageEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV: See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
for 5L-E: See pageEngine / Hybrid System>5L-E (ENGINE CONTROL)>ECM>REMOVAL
Check that the operation of the tachometer returns to normal.
The operation of the tachometer returns to normal.
OK
NG