There may be an open circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
| Symptom | Trouble Area |
|---|---|
|
*1: for LHD *2: for RHD |
|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher. | ·
Open in CAN main bus wire ·
ECM ·
Combination meter assembly ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector*1 ·
No. 3 CAN junction connector*1 ·
No. 4 CAN junction connector*2 ·
No. 5 CAN junction connector*1 ·
No. 6 CAN junction connector*2 ·
DLC3 CAN branch wire or connector |
for LHD
for RHD
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G48-6 (CANH) - G48-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to No. 5 CAN Junction Connector |
| *c | to No. 3 CAN Junction Connector | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G293-1 (CANH) - G293-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 5 CAN junction connector |
| G293-6 (CANH) - G293-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 3 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 3 CAN junction connector CAN main wire) | B |
| NG (No. 5 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the G293 No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 3 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | to Combination Meter Assembly | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G294-1 (CANH) - G294-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| G294-2 (CANH) - G294-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Combination meter assembly CAN main wire) | B |
| NG (No. 2 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the G294 No. 3 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-40 (CANH) - G6-39 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G293 No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 5 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | to No. 1 CAN Junction Connector | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G296-1 (CANH) - G296-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| G296-6 (CANH) - G296-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 CAN junction connector CAN main wire) | B |
| NG (No. 2 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the G296 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to No. 5 CAN Junction Connector |
| *c | to ECM | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A119-9 (CANH) - A119-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 5 CAN junction connector |
| A119-10 (CANH) - A119-21 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM CAN main wire) | B |
| NG (No. 5 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the A119 No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G183-25 (CANH) - G183-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 4 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to No. 6 CAN Junction Connector |
| *c | to No. 1 CAN Junction Connector | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G295-1 (CANH) - G295-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 6 CAN junction connector |
| G295-8 (CANH) - G295-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 CAN junction connector CAN main wire) | B |
| NG (No. 6 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the G295 No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to Combination Meter Assembly | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A119-9 (CANH) - A119-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 4 CAN junction connector |
| A119-10 (CANH) - A119-21 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Combination meter assembly CAN main wire) | B |
| NG (No. 4 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the A119 No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-40 (CANH) - G6-39 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G295 No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 6 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to ECM | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G297-1 (CANH) - G297-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 4 CAN junction connector |
| G297-2 (CANH) - G297-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM CAN main wire) | B |
| NG (No. 4 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the G297 No. 6 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G183-25 (CANH) - G183-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG