There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
| Symptom | Trouble Area |
|---|---|
|
*1: for LHD *2: for RHD |
|
| The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ. | ·
Short to +B in CAN main wires ·
Short to +B in CAN branch wire ·
DLC3 CAN branch wire or connector ·
ECM ·
Brake actuator assembly (skid cotrol ECU) ·
4 wheel drive control ECU ·
Airbag sensor assembly ·
Air conditioning amplifier assembly ·
Combination meter assembly ·
Main body ECU (multiplex network body ECU) ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector*1 ·
No. 3 CAN junction connector*1 ·
No. 4 CAN junction connector*2 ·
No. 5 CAN junction connector*1 ·
No. 6 CAN junction connector*2 |
for LHD
for RHD
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to No. 5 CAN Junction Connector |
| *c | to Airbag Sensor Assembly | *d | to No. 3 CAN Junction Connector |
| *e | Front view of DLC3 | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G293-1 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 5 CAN junction connector |
| G293-12 (CANL) - G48-16 (BAT) | |||
| G293-5 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Airbag sensor assembly |
| G293-16 (CANL) - G48-16 (BAT) | |||
| G293-6 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 3 CAN junction connector |
| G293-17 (CANL) - G48-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 3 CAN junction connector CAN main wire) | B |
| NG (No. 5 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G293 No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 3 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | to Combination Meter Assembly | *d | to Main Body ECU (Multiplex Network Body ECU) |
| *e | to DLC3 | *f | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G294-1 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 2 CAN junction connector |
| G294-12 (CANL) - G48-16 (BAT) | |||
| G294-2 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| G294-13 (CANL) - G48-16 (BAT) | |||
| G294-3 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Main body ECU (multiplex network body ECU) |
| G294-14 (CANL) - G48-16 (BAT) | |||
| G294-5 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | DLC3 |
| G294-16 (CANL) - G48-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DLC3 CAN branch wire) | B |
| NG (No. 2 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G293 No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 5 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | to 4 Wheel Drive Control ECU | *d | to Air Conditioning Amplifier Assembly |
| *e | to No. 1 CAN Junction Connector | *f | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G296-1 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 2 CAN junction connector |
| G296-12 (CANL) - G48-16 (BAT) | |||
| G296-2 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | 4 wheel drive control ECU |
| G296-13 (CANL) - G48-16 (BAT) | |||
| G296-4 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air conditioning amplifier assembly |
| G296-15 (CANL) - G48-16 (BAT) | |||
| G296-6 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 1 CAN junction connector |
| G296-17 (CANL) - G48-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 CAN junction connector CAN main wire) | B |
| NG (No. 2 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G296 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to No. 5 CAN Junction Connector |
| *c | to ECM | *d | to Brake Actuator Assembly (Skid Control ECU) |
| *e | Front view of DLC3 | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A119-9 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 5 CAN junction connector |
| A119-20 (CANL) - G48-16 (BAT) | |||
| A119-10 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ECM |
| A119-21 (CANL) - G48-16 (BAT) | |||
| A119-11 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Brake actuator assembly (skid control ECU) |
| A119-22 (CANL) - G48-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 5 CAN junction connector CAN main wire) | B |
| NG (Wire to ECU or sensor) | C |
A
B
C
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 4 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to No. 6 CAN Junction Connector |
| *c | to Main Body ECU (Multiplex Network Body ECU) | *d | to DLC3 |
| *e | to Airbag Sensor Assembly | *f | to No. 1 CAN Junction Connector |
| *g | Front view of DLC3 | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G295-1 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 6 CAN junction connector |
| G295-12 (CANL) - G48-16 (BAT) | |||
| G295-2 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Main body ECU (multiplex network body ECU) |
| G295-13 (CANL) - G48-16 (BAT) | |||
| G295-4 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | DLC3 |
| G295-15 (CANL) - G48-16 (BAT) | |||
| G295-5 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Airbag sensor assembly |
| G295-16 (CANL) - G48-16 (BAT) | |||
| G295-8 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 1 CAN junction connector |
| G295-19 (CANL) - G48-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 CAN junction connector CAN main wire) | B |
| NG (No. 6 CAN junction connector CAN main wire) | C |
| NG (DLC3 CAN branch wire) | D |
| NG (Wire to ECU or sensor) | E |
A
B
C
D
E
Reconnect the G295 No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to Combination Meter Assembly | *d | to Brake Actuator Assembly (Skid Control ECU) |
| *e | Front view of DLC3 | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A119-9 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 4 CAN junction connector |
| A119-20 (CANL) - G48-16 (BAT) | |||
| A119-10 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| A119-21 (CANL) - G48-16 (BAT) | |||
| A119-11 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Brake actuator assembly (skid control ECU) |
| A119-22 (CANL) - G48-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 4 CAN junction connector CAN main wire) | B |
| NG (Wire to ECU or sensor) | C |
A
B
C
Reconnect the G295 No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 6 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to ECM | *d | to 4 Wheel Drive Control ECU |
| *e | to Air Conditioning Amplifier Assembly | *f | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G297-1 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 4 CAN junction connector |
| G297-12 (CANL) - G48-16 (BAT) | |||
| G297-2 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ECM |
| G297-13 (CANL) - G48-16 (BAT) | |||
| G297-3 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | 4 wheel drive control ECU |
| G297-14 (CANL) - G48-16 (BAT) | |||
| G297-4 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air conditioning amplifier assembly |
| G297-15 (CANL) - G48-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 4 CAN junction connector CAN main wire) | B |
| NG (Wire to ECU or sensor) | C |
A
B
C
Reconnect all wire harness connector.
| *a | Front view of DLC3 |
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G48-6 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G48-14 (CANL) - G48-16 (BAT) |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG