Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325853 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

C382854C01
0.594,1.167 1.01,1.469 0.417,0.302 3.667,0.5 3.833,0.5 3.833,0.5 3.99,1.271 true 3.865,0.24 4.031,0.24 4.031,0.24 4.177,1.292 true 4.875,0.74 4.708,0.74 4.708,0.74 4.396,1.302 true 4.927,1.979 4.76,1.979 4.76,1.979 4.427,1.542 true 3.896,2.448 4.063,2.448 4.063,2.448 4.208,1.552 true 3.583,2.25 3.75,2.25 3.75,2.25 4.01,1.531 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.625,1.219 1.01,1.458 0.385,0.24 10 false A119 3.115,0.417 3.75,0.698 0.635,0.281 10 false CANH*b 3.333,0.156 3.969,0.438 0.635,0.281 10 false CANH*c 4.938,0.667 5.573,0.948 0.635,0.281 10 false CANH*d 4.969,1.906 5.604,2.188 0.635,0.281 10 false CANL*d 3.365,2.385 4,2.667 0.635,0.281 10 false CANL*c 3.021,2.167 3.656,2.448 0.635,0.281 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b
·

for No. 5 CAN Junction Connector (for LHD)

·

for No. 4 CAN Junction Connector (for RHD)


*c
·

for ECM (for LHD)

·

for Combination Meter Assembly (for RHD)


*d for Brake Actuator Assembly (Skid Control ECU)



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: for LHD

*2: for RHD

A119-9 (CANH) R*1, B*2
·

No. 5 CAN junction connector*1

·

No. 4 CAN junction connector*2


A119-20 (CANL) W
A119-10 (CANH) LG
·

ECM*1

·

Combination meter assembly*2


A119-21 (CANL) W
A119-11 (CANH) B*1, R*2 Brake actuator assembly (skid control ECU)
A119-22 (CANL) W




NO. 2 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C382852C01
1.052,1.24 1.458,1.49 0.406,0.25 2.458,0.594 2.708,0.594 2.708,0.594 2.708,1.375 true 2.469,2.135 2.719,2.135 2.719,2.135 2.719,1.719 true 3.156,0.385 3.406,0.385 3.406,0.385 3.406,1.385 true 3.167,2.385 3.417,2.385 3.417,2.385 3.417,1.719 true 3.75,0.385 3.583,0.385 3.583,0.385 3.583,1.385 true 3.75,2.385 3.583,2.385 3.583,2.385 3.583,1.719 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.083,1.292 1.583,1.531 0.5,0.24 10 false G293 1.896,0.521 2.563,0.76 0.667,0.24 10 false CANH*b 1.938,2.052 2.604,2.292 0.667,0.24 10 false CANL*b 2.604,0.292 3.271,0.531 0.667,0.24 10 false CANH*c 2.646,2.323 3.313,2.563 0.667,0.24 10 false CANL*c 3.802,0.313 4.469,0.552 0.667,0.24 10 false CANH*d 3.802,2.313 4.469,2.552 0.667,0.24 10 false CANL*d
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b for No. 5 CAN Junction Connector
*c for Airbag Sensor Assembly *d for No. 3 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
G293-1 (CANH) GR No. 5 CAN junction connector
G293-12 (CANL) W
G293-5 (CANH) Y Airbag sensor assembly
G293-16 (CANL) W
G293-6 (CANH) LG No. 3 CAN junction connector
G293-17 (CANL) W




NO. 3 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C382856C01
1.813,1.198 2.198,1.427 0.385,0.229 2.542,0.542 2.708,0.542 2.708,0.542 2.708,1.375 true 2.552,2.24 2.719,2.24 2.719,2.24 2.719,1.74 true 2.708,0.354 2.875,0.354 2.875,0.354 2.875,1.354 true 2.719,2.458 2.885,2.458 2.885,2.458 2.885,1.729 true 2.885,0.198 3.052,0.198 3.052,0.198 3.052,1.365 true 2.896,2.625 3.063,2.625 3.063,2.625 3.063,1.729 true 3.573,0.167 3.406,0.167 3.406,0.167 3.406,1.333 true 3.573,2.615 3.406,2.615 3.406,2.615 3.406,1.698 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,1.229 2.219,1.427 0.385,0.198 10 false G294 1.969,0.458 2.552,0.688 0.583,0.229 10 false CANH*b 2.031,2.156 2.615,2.385 0.583,0.229 10 false CANL*b 2.135,0.271 2.719,0.5 0.583,0.229 10 false CANH*c 2.188,2.365 2.771,2.594 0.583,0.229 10 false CANL*c 2.333,0.094 2.917,0.323 0.583,0.229 10 false CANH*d 2.375,2.531 2.958,2.76 0.583,0.229 10 false CANL*d 3.667,0.104 4.25,0.333 0.583,0.229 10 false CANH*e 3.625,2.552 4.208,2.781 0.583,0.229 10 false CANL*e
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b for No. 2 CAN Junction Connector
*c for Combination Meter Assembly *d for Main Body ECU (Multiplex Network Body ECU)
*e for DLC3 - -



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. Wiring Color Connected to
G294-1 (CANH) LG No. 2 CAN junction connector
G294-12 (CANL) W
G294-2 (CANH) V Combination meter assembly
G294-13 (CANL) W
G294-3 (CANH) L Main body ECU (multiplex network body ECU)
G294-14 (CANL) W
G294-5 (CANH) R DLC3
G294-16 (CANL) W




NO. 4 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C382852C03
1.052,1.24 1.458,1.49 0.406,0.25 2.135,0.938 2.385,0.938 2.385,0.938 2.656,1.406 true 2.188,1.969 2.438,1.969 2.438,1.969 2.719,1.698 true 2.979,0.406 3.229,0.406 3.229,0.406 3.229,1.406 true 2.979,2.385 3.229,2.385 3.229,2.385 3.229,1.719 true 3.615,0.385 3.448,0.385 3.448,0.385 3.448,1.385 true 3.594,2.385 3.427,2.385 3.427,2.385 3.427,1.719 true 2.24,0.625 2.49,0.625 2.49,0.625 2.875,1.385 true 2.365,2.208 2.615,2.208 2.615,2.208 2.906,1.667 true 4.427,0.625 4.26,0.625 4.26,0.625 3.958,1.375 true 4.396,2.146 4.229,2.146 4.229,2.146 3.938,1.74 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.083,1.292 1.583,1.531 0.5,0.24 10 false G295 1.594,0.823 2.26,1.063 0.667,0.24 10 false CANH*b 1.656,1.885 2.323,2.125 0.667,0.24 10 false CANL*b 1.719,0.542 2.385,0.781 0.667,0.24 10 false CANH*c 1.833,2.125 2.5,2.365 0.667,0.24 10 false CANL*c 2.448,0.323 3.115,0.563 0.667,0.24 10 false CANH*d 2.458,2.302 3.125,2.542 0.667,0.24 10 false CANL*d 3.667,0.313 4.333,0.552 0.667,0.24 10 false CANH*e 3.646,2.302 4.313,2.542 0.667,0.24 10 false CANL*e 4.469,0.552 5.135,0.792 0.667,0.24 10 false CANH*f 4.448,2.073 5.115,2.313 0.667,0.24 10 false CANL*f
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b for No. 6 CAN Junction Connector
*c for Main Body ECU (Multiplex Network Body ECU) *d for DLC3
*e for Airbag Sensor Assembly *f for No. 1 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
G295-1 (CANH) GR No. 6 CAN junction connector
G295-12 (CANL) W
G295-2 (CANH) L Main body ECU (multiplex network body ECU)
G295-13 (CANL) W
G295-4 (CANH) R DLC3
G295-15 (CANL) W
G295-5 (CANH) P Airbag sensor assembly
G295-16 (CANL) W
G295-8 (CANH) B No. 1 CAN junction connector
G295-19 (CANL) W




NO. 5 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C382852C02
1.052,1.24 1.458,1.49 0.406,0.25 2.458,0.594 2.708,0.594 2.708,0.594 2.708,1.375 true 2.469,2.135 2.719,2.135 2.719,2.135 2.719,1.719 true 2.625,0.385 2.875,0.385 2.875,0.385 2.875,1.385 true 2.604,2.385 2.854,2.385 2.854,2.385 2.854,1.719 true 3.396,0.385 3.229,0.385 3.229,0.385 3.229,1.385 true 3.375,2.385 3.208,2.385 3.208,2.385 3.208,1.719 true 3.74,0.563 3.573,0.563 3.573,0.563 3.573,1.365 true 3.75,2.177 3.583,2.177 3.583,2.177 3.583,1.729 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.083,1.292 1.583,1.531 0.5,0.24 10 false G296 1.896,0.521 2.563,0.76 0.667,0.24 10 false CANH*b 1.938,2.052 2.604,2.292 0.667,0.24 10 false CANL*b 2.073,0.292 2.74,0.531 0.667,0.24 10 false CANH*c 2.073,2.323 2.74,2.563 0.667,0.24 10 false CANL*c 3.448,0.313 4.115,0.552 0.667,0.24 10 false CANH*d 3.406,2.313 4.073,2.552 0.667,0.24 10 false CANL*d 3.781,0.49 4.448,0.729 0.667,0.24 10 false CANH*e 3.792,2.094 4.458,2.333 0.667,0.24 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b for No. 2 CAN Junction Connector
*c for 4 Wheel Drive Control ECU *d for Air Conditioning Amplifier Assembly
*e for No. 1 CAN Junction Connector - -



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
G296-1 (CANH) GR No. 2 CAN junction connector
G296-12 (CANL) W
G296-2 (CANH) G 4 wheel drive control ECU
G296-13 (CANL) W
G296-4 (CANH) BR Air conditioning amplifier assembly
G296-15 (CANL) W
G296-6 (CANH) R No. 1 CAN junction connector
G296-17 (CANL) W




NO. 6 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C382852C04
1.052,1.24 1.458,1.49 0.406,0.25 2.458,0.594 2.708,0.594 2.708,0.594 2.708,1.375 true 2.469,2.135 2.719,2.135 2.719,2.135 2.719,1.719 true 2.615,0.385 2.865,0.385 2.865,0.385 2.865,1.385 true 2.625,2.385 2.875,2.385 2.875,2.385 2.875,1.719 true 3.406,0.458 3.24,0.458 3.24,0.458 3.24,1.385 true 3.406,2.281 3.24,2.281 3.24,2.281 3.24,1.75 true 3.229,0.198 3.063,0.198 3.063,0.198 3.063,1.417 true 3.229,2.594 3.063,2.594 3.063,2.594 3.063,1.74 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.083,1.292 1.583,1.531 0.5,0.24 10 false G297 1.896,0.521 2.563,0.76 0.667,0.24 10 false CANH*b 1.938,2.052 2.604,2.292 0.667,0.24 10 false CANL*b 2.083,0.292 2.75,0.531 0.667,0.24 10 false CANH*c 2.104,2.323 2.771,2.563 0.667,0.24 10 false CANL*c 3.469,0.385 4.135,0.625 0.667,0.24 10 false CANH*e 3.458,2.219 4.125,2.458 0.667,0.24 10 false CANL*e 3.302,0.135 3.969,0.375 0.667,0.24 10 false CANH*d 3.271,2.531 3.938,2.771 0.667,0.24 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b for No. 4 CAN Junction Connector
*c for ECM *d for 4 Wheel Drive Control ECU
*e for Air Conditioning Amplifier Assembly - -



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
G297-1 (CANH) GR No. 4 CAN junction connector
G297-12 (CANL) W
G297-2 (CANH) LG ECM
G297-13 (CANL) W
G297-3 (CANH) G 4 wheel drive control ECU
G297-14 (CANL) W
G297-4 (CANH) BR Air conditioning amplifier assembly
G297-15 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C349818C21
1.625,1.313 2.042,1.583 0.417,0.271 3.865,1.125 3.865,0.51 3.865,0.51 4.052,0.51 true 3.51,1.125 3.51,0.51 3.51,0.51 3.313,0.51 true 4.417,2.24 4.229,2.24 4.229,2.24 4.229,1.708 true 3.667,2.24 3.865,2.24 3.865,2.24 3.865,1.708 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.156,0.458 4.792,0.688 0.635,0.229 10 false CANH 3.26,2.198 3.896,2.427 0.635,0.229 10 false CANL 3.042,0.469 3.677,0.698 0.635,0.229 10 false CG 4.51,2.177 5.146,2.406 0.635,0.229 10 false BAT 1.729,1.396 2.365,1.625 0.635,0.229 10 false G48
*a Front view of DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G48-6 (CANH) - G48-4 (CG) R - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G48-14 (CANL) - G48-4 (CG) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G48-6 (CANH) - G48-16 (BAT) R - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G48-14 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.

C382923C01
3.417,0.333 3.833,0.583 0.417,0.25 2.333,0.75 2.5,0.75 2.5,0.75 3.177,1.188 true 4.25,1.167 4.583,1 4.583,1 4.75,1 true 4.25,1.604 4.583,1.438 4.583,1.438 4.75,1.438 true 4.26,1.906 4.604,2.052 4.604,2.052 4.771,2.052 true 0.104,0.042 0.417,0.24 0.313,0.198 10 false *a 3.469,0.365 3.917,0.594 0.448,0.229 10 false G183 1.938,0.656 2.385,0.885 0.448,0.229 10 false BATT 4.823,0.938 5.271,1.167 0.448,0.229 10 false EC 4.844,1.385 5.521,1.615 0.677,0.229 10 false CANH 4.833,1.979 5.51,2.208 0.677,0.229 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G183-25 (CANH) - G183-31 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G183-25 (CANH) - G183-7 (EC) LG - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G183-31 (CANL) - G183-7 (EC) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G183-25 (CANH) - G183-2 (BATT) LG - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G183-31 (CANL) - G183-2 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TERMINALS OF ECU

a.
U148964C02
2.51,1.25 2.781,2.021 2.781,2.021 2.917,2.021 true 1.115,0.844 0.708,0.354 0.708,0.354 0.573,0.354 true 1.313,1.365 1.635,1.917 1.635,1.917 1.781,1.917 true 1.302,1.219 0.813,1.854 0.813,1.854 0.677,1.854 true 0.083,0.271 0.542,0.417 0.458,0.146 10 false GND1 3,1.917 3.313,2.063 0.313,0.146 10 false BM 1.698,0.125 2.01,0.313 0.313,0.188 10 false A6 1.844,1.844 2.365,2.063 0.521,0.219 10 false CANH 0.323,1.781 0.844,2 0.521,0.219 10 false CANL 0.042,0.042 0.5,0.188 0.458,0.146 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A6-25 (CANH) - A6-14 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A6-25 (CANH) - A6-1 (GND1) B - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A6-14 (CANL) - A6-1 (GND1) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A6-25 (CANH) - A6-24 (BM) B - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A6-14 (CANL) - A6-24 (BM) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379594C10
1.531,0.229 1.969,0.427 0.438,0.198 0.896,2.427 0.729,2.427 0.729,2.427 0.563,1.927 true 1,0.865 1.198,0.865 1.198,0.865 1.792,1.719 true 1.396,0.646 1.594,0.646 1.594,0.646 1.917,1.719 true 2.385,0.781 2.219,0.781 2.219,0.781 2.135,1.75 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.021,0.594 1.479,0.792 0.458,0.198 10 false CANL 0.594,0.781 1.052,0.979 0.458,0.198 10 false CANH 2.438,0.698 2.896,0.896 0.458,0.198 10 false GND 0.948,2.344 1.406,2.542 0.458,0.198 10 false B 1.573,0.24 2.031,0.438 0.458,0.198 10 false G25
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) BR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G25-11 (CANH) - G25-14 (GND) BR - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G25-12 (CANL) - G25-14 (GND) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G25-11 (CANH) - G25-21 (B) BR - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G25-12 (CANL) - G25-21 (B) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.
C227529C11
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 false *a 0.198,2.083 0.51,2.24 0.313,0.156 10 false *b 0.479,2.573 0.823,2.781 0.344,0.208 10 false G48 0.458,1 0.802,1.208 0.344,0.208 10 false G1 2.75,0.583 3.292,0.792 0.542,0.208 10 false CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 false CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 false BAT 1,1.604 1.542,1.813 0.542,0.208 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G1-13 (CANH) - G1-25 (E1) Y - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G1-22 (CANL) - G1-25 (E1) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G1-13 (CANH) - G48-16 (BAT) Y - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G1-22 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379594C16
1.531,0.229 1.969,0.427 0.438,0.198 0.896,2.563 1.063,2.563 1.063,2.563 1.167,1.969 true 0.333,2.417 0.5,2.417 0.5,2.417 0.563,1.927 true 2.51,2.615 2.708,2.615 2.708,2.615 2.906,1.917 true 2.146,2.365 2.344,2.365 2.344,2.365 2.792,1.917 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.698,2.281 2.156,2.479 0.458,0.198 10 false CANL 2.104,2.521 2.563,2.719 0.458,0.198 10 false CANH 0.719,2.51 1.177,2.708 0.458,0.198 10 false B 1.656,0.25 2.115,0.448 0.458,0.198 10 false G6 0.094,2.365 0.552,2.563 0.458,0.198 10 false E2
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G6-40 (CANH) - G6-21 (E2) V - BR HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G6-39 (CANL) - G6-21 (E2) W - BR LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G6-40 (CANH) - G6-26 (B) V - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G6-39 (CANL) - G6-26 (B) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4 WHEEL DRIVE CONTROL ECU


Refer to Terminals of ECU.

Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4 wheel drive control ECU connectors.

C382831C01
2.167,0.083 2.604,0.313 0.438,0.229 5.292,0.177 5.729,0.406 0.438,0.229 3.5,0.906 3.771,0.406 3.771,0.406 3.938,0.406 true 3.51,1.104 3.74,1.469 3.74,1.469 3.906,1.469 true 1.115,1.094 0.979,1.365 0.979,1.365 0.781,1.365 true 5.948,1.073 6.177,1.438 6.177,1.438 6.344,1.438 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 2.25,0.115 2.563,0.313 0.313,0.198 10 false G53 5.396,0.219 5.708,0.417 0.313,0.198 10 false G54 3.979,0.333 4.417,0.531 0.438,0.198 10 false CANH 3.958,1.385 4.396,1.583 0.438,0.198 10 false CANL 0.542,1.292 0.979,1.49 0.438,0.198 10 false +B 6.396,1.354 6.833,1.552 0.438,0.198 10 false GND
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G53-20 (CANH) - G53-40 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G53-20 (CANH) - G54-10 (GND) G - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G53-40 (CANL) - G54-10 (GND) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G53-20 (CANH) - G53-21 (+B) G - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G53-40 (CANL) - G53-21 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.

C382925C01
4.76,0.563 5.177,0.813 0.417,0.25 1.417,0.5 1.833,0.75 0.417,0.25 1.417,2.167 1.583,2.167 1.583,2.167 1.75,1.531 true 4.417,0.833 4.583,0.833 4.583,0.833 4.927,1.208 true 1.854,1.5 2.021,2.167 2.021,2.167 2.188,2.167 true 5.469,1.573 5.573,1.875 5.573,1.875 5.74,1.875 true 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 2.229,2.094 2.76,2.292 0.531,0.198 10 false CANH 1,2.094 1.531,2.292 0.531,0.198 10 false CANL 1.5,0.531 2.031,0.729 0.531,0.198 10 false G64 4.844,0.604 5.375,0.802 0.531,0.198 10 false G48 4.125,0.76 4.656,0.958 0.531,0.198 10 false CG 3.76,0.167 4.073,0.365 0.313,0.198 10 false *b 5.802,1.802 6.333,2 0.531,0.198 10 false BAT
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G64-14 (CANH) - G48-4 (CG) L - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G64-13 (CANL) - G48-4 (CG) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G64-14 (CANH) - G48-16 (BAT) L - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G64-13 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher