Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  P0340  Camshaft Position Sensor Circuit  


DESCRIPTION

The camshaft position sensor (G2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The G2 signal plate has 3 teeth on its outer circumference and is installed on the exhaust camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the MRE change, causing fluctuations in the magnetic field that generate a voltage in the MRE.

The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G2 signal, and detects the crankshaft angle based on the NE signal.

P0016
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle engine for 1 second Phase deviation in crankshaft and camshaft position sensor signals with an engine speed of 650 to 3000 rpm occurs a certain number of times.
(1 trip detection logic)
·

Camshaft position sensor

·

Crankshaft position sensor

·

Exhaust camshaft

·

ECM



P0340
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Crank engine for 4 seconds STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more.
(2 trip detection logic)
·

Camshaft position sensor

·

Exhaust camshaft

·

ECM


Idle engine for 1 second STA off:
Camshaft position sensor signal is not input with an engine speed of 650 rpm or more.
(1 trip detection logic)

HINT:

If DTC P0016 or P0340 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




Reference: Inspection using an oscilloscope.

A340471E01
3.042,1.021 3.375,1.281 0.333,0.26 10 false GND 3.031,1.542 3.365,1.771 0.333,0.229 10 false GND 0.052,0.854 0.406,1.094 0.354,0.24 10 false G2 0.063,1.396 0.354,1.625 0.292,0.229 10 false NE 2.729,0.156 3.323,0.354 0.594,0.198 10 false 2 V/DIV. 1.292,1.833 2.5,2 1.208,0.167 10 false 20 msec./DIV.

HINT:

The correct waveform is as shown.

ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling after engine warmed


WIRING DIAGRAM

A348533E11
0.938,2.01 2.677,2.219 1.74,0.208 10 false Camshaft Position Sensor 0.875,4.063 2.708,4.271 1.833,0.208 10 false Crankshaft Position Sensor 5.167,4.156 5.604,4.344 0.438,0.188 10 false ECM 2.229,0.906 2.427,1.083 0.198,0.177 10 false 3 1.938,0.781 2.229,0.979 0.292,0.198 10 false VC 1.896,3.104 2.25,3.302 0.354,0.198 10 false NE- 2.229,1.281 2.427,1.458 0.198,0.177 10 false 2 2.219,1.646 2.417,1.823 0.198,0.177 10 false 1 2.229,2.875 2.427,3.052 0.198,0.177 10 false 3 2.229,3.24 2.427,3.417 0.198,0.177 10 false 2 2.219,3.615 2.417,3.792 0.198,0.177 10 false 1 5.156,3.99 5.604,4.177 0.448,0.188 10 false C152 0.948,1.833 1.365,2.042 0.417,0.208 10 false C170 0.885,3.885 1.177,4.083 0.292,0.198 10 false r7 4.708,0.802 5.156,1.021 0.448,0.219 10 false VCG 1.844,1.156 2.292,1.354 0.448,0.198 10 false G22- 4.698,1.156 5.146,1.354 0.448,0.198 10 false G2- 1.802,1.521 2.344,1.719 0.542,0.198 10 false G22+ 4.688,1.521 5.229,1.719 0.542,0.198 10 false G2+ 1.927,2.76 2.219,2.958 0.292,0.198 10 false VC 4.677,2.76 5.271,2.948 0.594,0.188 10 false VCNE 4.688,3.125 5.042,3.323 0.354,0.198 10 false NE- 1.875,3.469 2.271,3.667 0.396,0.198 10 false NE+ 4.688,3.479 5.083,3.677 0.396,0.198 10 false NE+ 4.448,0.885 4.646,1.063 0.198,0.177 10 false 17 4.438,1.271 4.635,1.448 0.198,0.177 10 false 18 4.438,1.646 4.677,1.823 0.24,0.177 10 false 27 4.438,2.865 4.635,3.042 0.198,0.177 10 false 20 4.438,3.24 4.635,3.417 0.198,0.177 10 false 19 4.438,3.594 4.635,3.771 0.198,0.177 10 false 28

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result
Result Proceed to
Cranking is OK A
Does not crank at all B



A

2.INSPECT ECM TERMINAL VOLTAGE (CAMSHAFT POSITION SENSOR)

B

2.INSPECT ECM TERMINAL VOLTAGE (CAMSHAFT POSITION SENSOR)
a.

Inspect the ECM using an oscilloscope.

i.

While the engine is idling, check the waveform between the terminals of the ECM connector.

U169476E01
5.896,0.896 6.208,0.229 false 5.854,0.896 5.167,1.375 false 5.896,0.948 5.833,1.385 false 5.938,0.948 6.49,1.375 false 0.063,0.625 0.354,0.823 0.292,0.198 10 false G2 0.063,1.094 0.354,1.292 0.292,0.198 10 false NE 3.458,1.24 3.854,1.438 0.396,0.198 10 false GND 3.469,0.802 3.865,1 0.396,0.198 10 false GND 3.281,0.042 3.969,0.24 0.688,0.198 10 false 2V/DIV. 5.615,0.208 6.031,0.375 0.417,0.167 10 false C152 4.885,1.396 5.469,1.594 0.583,0.198 10 false 19 (NE-) 5.563,1.396 6.219,1.594 0.656,0.198 10 false 28 (NE+) 6.323,1.396 6.958,1.594 0.635,0.198 10 false 27 (G2+) 6.271,0.135 6.854,0.333 0.583,0.198 10 false 18 (G2-) 4.125,0 4.417,0.198 0.292,0.198 10 false *a

Text in Illustration
*a Component with harness connected
(ECM)
- -

OK:
Tester Connection Tester Range Condition Specified Condition
C152-27 (G2+) - C152-18 (G2-) 2 V/DIV.
20 msec./DIV.
Idling Correct waveform as shown in illustration
C152-28 (NE+) - C152-19 (NE-) 2 V/DIV.
20 msec./DIV.
Idling Correct waveform as shown in illustration





OK

3.INSPECT CAMSHAFT POSITION SENSOR AND CRANKSHAFT POSITIONSENSOR TIMING

NG

7.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
3.INSPECT CAMSHAFT POSITION SENSOR AND CRANKSHAFT POSITIONSENSOR TIMING
a.

Inspect the ECM using an oscilloscope.


b.

While the engine is idling, check the waveform between the terminals of the ECM connector.


c.

Inspect the camshaft position sensor and crankshaft position sensor timing.

A348543E01
5.885,1.25 6.344,1.448 0.458,0.198 10 false GND 5.896,1.948 6.354,2.146 0.458,0.198 10 false GND 0.625,1.031 1.406,1.219 0.781,0.188 10 false G2 Signal 0.615,1.719 1.354,1.906 0.74,0.188 10 false Ne Signal 5.906,0.438 6.646,0.625 0.74,0.188 10 false 2 V/DIV. 3.094,2.417 4.167,2.604 1.073,0.188 10 false 20 msec./DIV. 3.302,0.26 4.073,0.521 0.771,0.26 10 false 720°CA

OK:
Tester Connection Tester Range Condition Specified Condition
C152-27 (G2+) - C152-18 (G2-) 2 V/DIV.
20 msec./DIV.
Idling Correct waveform as shown in illustration
C152-28 (NE+) - C152-19 (NE-) 2 V/DIV.
20 msec./DIV.
Idling Correct waveform as shown in illustration




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

6.CHECK ENGINE MECHANICAL SYSTEM
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off for 30 seconds or more.


f.

Start the engine and idle it for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
DTC P0016 or P0340 is output A
DTC is not output B



A

5.REPLACE ECM

B

5.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK ENGINE MECHANICAL SYSTEM
a.

When the G2 signal appears to be malfunctioning, check the exhaust camshaft.

·

If the teeth of the timing rotor are damaged, perform replacement (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).



b.

When the Ne signal appears to be malfunctioning, check the following parts.

·

Installation condition of the crankshaft position sensor.

·

Crank angle sensor plate.



c.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain (See page Engine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A316078E12
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG

Check the sensor installation.

Text in Illustration
*a Clearance

OK:

Camshaft position sensor is installed correctly.




OK

8.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)

NG

11.SECURELY REINSTALL CAMSHAFT POSITION SENSOR
8.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Inspect the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.




OK

9.REPLACE CAMSHAFT POSITION SENSOR

NG

10.REPLACE EXHAUST CAMSHAFT
9.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EXHAUST CAMSHAFT
a.

Replace the exhaust camshaft.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.SECURELY REINSTALL CAMSHAFT POSITION SENSOR
a.

Securely reinstall the camshaft position sensor.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off for 30 seconds or more.


f.

Start the engine and idle it for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output.



NEXT

END