Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.4 to 1.0 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.6 to 4.2 V when the throttle valve is fully opened.

The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.

A298509E01
2.073,2.635 2.323,2.635 2.323,2.635 2.74,2.365 true 2.396,0.51 2.563,0.51 2.563,0.51 2.729,1.156 true 3.281,0.406 3.063,0.406 3.063,0.406 2.875,1.677 true 4.698,2.771 5.156,2.969 0.458,0.198 10 ECM 3.844,2.177 4.302,2.375 0.458,0.198 10 EVLU 3.927,1.563 4.385,1.76 0.458,0.198 10 VLU 3.833,0.948 4.292,1.146 0.458,0.198 10 VCVL 3.49,0.948 3.948,1.146 0.458,0.198 10 VC 3.49,1.563 3.948,1.76 0.458,0.198 10 VTA 3.49,2.167 3.948,2.365 0.458,0.198 10 E2 1.563,2.552 2.135,2.781 0.573,0.229 10 Magnet 1.885,0.417 2.458,0.646 0.573,0.229 10 Magnet 3.344,0.323 3.917,0.552 0.573,0.229 10 Hall IC 4.729,0.885 5.302,1.115 0.573,0.229 10 5 V 2.052,2.792 3.604,3.073 1.552,0.281 10 Throttle Position Sensor

P0122
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 seconds Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open or short in VLU circuit

·

Open in VC circuit

·

ECM



P0123
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 seconds Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open in E2 circuit

·

VC and VLU circuits are short-circuited

·

ECM



HINT:

If DTC P0122 and/or P0123 is stored, the following symptoms may appear:


- Intake booming noise

- Black smoke

- Lack of power

- Vibration at engine stop

- Turbo overspeed, turbo damage


MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

A302636E02
2.104,1.167 2.313,1.052 false 2.094,2.74 2.302,2.625 false 3.313,1 3.469,0.417 3.469,0.417 3.615,0.417 false 4.604,2.656 4.719,3.031 4.719,3.031 4.823,3.031 false 0.146,1.365 1.635,1.781 1.49,0.417 10 false Throttle Position Sensor Output Voltage (V) 2.042,0.625 2.563,0.844 0.521,0.219 10 false Closed 1.99,0.885 2.333,1.063 0.344,0.177 10 false 5.00 1.802,1.115 2.146,1.292 0.344,0.177 10 false 4.80 2,1.365 2.396,1.542 0.396,0.177 10 false 4.13 2,2.406 2.344,2.583 0.344,0.177 10 false 0.69 1.844,2.75 2.188,2.927 0.344,0.177 10 false 0.20 2.677,2.729 3.917,2.948 1.24,0.219 10 false Range of Operation 3.656,0.333 4.552,0.573 0.896,0.24 10 false Stores P0123 3.938,0.604 4.458,0.823 0.521,0.219 10 false Open 4.865,2.948 5.823,3.177 0.958,0.229 10 false Stores P0122 2.281,3.177 2.438,3.344 0.156,0.167 10 false 0 4.083,3.177 4.396,3.344 0.313,0.167 10 false 86° 2.656,3.385 4.531,3.635 1.875,0.25 10 false Throttle Valve Opening Angle

WIRING DIAGRAM

A351115E02
0.563,3.865 2.531,4.073 1.969,0.208 10 false Diesel Throttle Body Assembly 0.563,3.656 0.823,3.865 0.26,0.208 10 false r5 5.771,3.74 6.25,3.948 0.479,0.208 10 false ECM 4.979,0.865 5.406,1.031 0.427,0.167 10 false C151 4.969,2.438 5.396,2.604 0.427,0.167 10 false C152 4.99,1.406 5.417,1.573 0.427,0.167 10 false C151 4.99,2.958 5.417,3.125 0.427,0.167 10 false C152 4.99,1.917 5.417,2.083 0.427,0.167 10 false C151 5.063,0.656 5.281,0.823 0.219,0.167 10 false 29 5.115,2.771 5.333,2.938 0.219,0.167 10 false 5 5.094,2.25 5.313,2.417 0.219,0.167 10 false 6 5.073,1.719 5.292,1.885 0.219,0.167 10 false 20 5.063,1.208 5.281,1.375 0.219,0.167 10 false 21 1.865,0.75 2.115,0.917 0.25,0.167 10 false VC 1.865,2.958 2.094,3.125 0.229,0.167 10 false M- 5.406,1.813 5.833,1.979 0.427,0.167 10 false EVLU 5.406,1.271 5.833,1.438 0.427,0.167 10 false VLU 5.406,0.76 5.833,0.927 0.427,0.167 10 false VCVL 1.844,2.438 2.104,2.604 0.26,0.167 10 false M+ 1.885,1.802 2.125,1.969 0.24,0.167 10 false E2 1.792,1.271 2.135,1.438 0.344,0.167 10 false VTA 5.417,2.958 5.844,3.125 0.427,0.167 10 false M- 5.417,2.427 5.844,2.594 0.427,0.167 10 false M+ 2.156,0.75 2.323,0.917 0.167,0.167 10 false 5 2.146,2.323 2.313,2.49 0.167,0.167 10 false 2 2.156,1.271 2.323,1.438 0.167,0.167 10 false 6 2.156,2.844 2.323,3.01 0.167,0.167 10 false 1 2.156,1.802 2.323,1.969 0.167,0.167 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ECM (POWER SOURCE OF THROTTLE POSITION SENSOR)
a.
U169390E02
1.573,1.635 1.104,2.406 true 1.615,1.698 2.24,2.417 true 1.354,0.927 1.771,1.083 0.417,0.156 10 false C151 0.708,2.469 1.417,2.625 0.708,0.156 10 false 20 (EVLU) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 1.927,2.448 2.635,2.604 0.708,0.156 10 false 29 (VCVL)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C151-29 (VCVL) - C151-20 (EVLU) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

2.INSPECT THROTTLE POSITION SENSOR VOLTAGE (VLU VOLTAGE)

NG

8.REPLACE ECM
2.INSPECT THROTTLE POSITION SENSOR VOLTAGE (VLU VOLTAGE)
a.
U169391E02
1.531,1.635 1.104,2.406 true 1.583,1.635 2.25,2.406 true 1.354,0.938 1.729,1.094 0.375,0.156 10 false C151 1.854,2.427 2.563,2.583 0.708,0.156 10 false 20 (EVLU) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 0.74,2.427 1.448,2.583 0.708,0.156 10 false 21 (VLU)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C151-21 (VLU) - C151-20 (EVLU) Engine switch on (IG) 3.6 to 4.2 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

3.CHECK DTC OUTPUT

NG

4.CHECK HARNESS AND CONNECTOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off.


d.

Turn the engine switch on (IG) for 3 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTC P0122 or P0123 is output B




A

B

8.REPLACE ECM
4.CHECK HARNESS AND CONNECTOR
a.
U169414E01
0.217,0.424 0.421,0.600 0.205,0.177 10 *a 0.605,1.247 0.824,1.416 0.219,0.169 10 r5 2.079,1.758 2.306,1.931 0.228,0.172 10 VC 1.205,1.776 1.421,1.936 0.216,0.161 10 E2 1.935,1.416 2.146,1.758 false 1.657,1.416 1.34,1.776 false

Disconnect the diesel throttle body assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r5-5 (VC) - r5-3 (E2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Diesel Throttle Body Assembly)


c.

Reconnect the throttle position sensor connector.



OK

5.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r5-6 (VTA) - C151-21 (VLU) Always Below 1 Ω
r5-3 (E2) - C151-20 (EVLU) Always Below 1 Ω
r5-6 (VTA) or C151-21 (VLU) - Body ground and other terminals Always 10 kΩ or higher
r5-3 (E2) or C151-20 (EVLU) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the diesel throttle body assembly connector.


e.

Reconnect the ECM connector.



OK

6.CHECK ECM (CHECK RESISTANCE)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM (CHECK RESISTANCE)
a.
U169415E01
0.217,0.424 0.421,0.600 0.205,0.177 10 *a 0.605,1.247 0.824,1.416 0.219,0.169 10 r5 2.044,1.758 2.272,1.931 0.228,0.172 10 VC 1.205,1.776 1.421,1.936 0.216,0.161 10 E2 1.935,1.416 2.146,1.758 false 1.657,1.416 1.34,1.776 false 2.414,1.758 2.787,1.931 0.373,0.172 10 VTA 2.099,1.399 2.515,1.758 false

Disconnect the diesel throttle body assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r5-5 (VC) - r5-6 (VTA) Engine switch off No short or open
r5-6 (VTA) - r5-3 (E2)


Text in Illustration
*a Front view of wire harness connector
(to Diesel Throttle Body Assembly)


c.

Reconnect the diesel throttle body assembly connector.



OK

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

8.REPLACE ECM
7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off.


d.

Turn the engine switch on (IG) for 3 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END