Refer to DTC P0335 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0335).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 4 seconds or more | Output voltage of crankshaft position sensor is less than 0.3 V for 4 seconds.
(1 trip detection logic) |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 4 seconds or more | Output voltage of crankshaft position sensor is higher than 4.7 V for 4 seconds.
(1 trip detection logic) |
·
Crankshaft position sensor ·
Crankshaft (crank angle sensor plate) ·
ECM |
If DTC P0337 or P0338 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
| ECM Terminal Name | Between G2+ and G2-
Between NE+ and NE- |
| Tester Range | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V, the ECM stores a DTC.
Refer to DTC P0335 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0335).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Disconnect the crankshaft position sensor connector.
Turn the engine switch on (IG) for 4 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
| Result | Proceed to |
|---|---|
| DTC does not change | A |
| DTC changes | B |
A
B
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C152-20 (VCNE) - C152-19 (NE-) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r7-1 (NE+) - C152-28 (NE+) | Always | Below 1 Ω |
| r7-2 (NE-) - C152-19 (NE-) | Always | Below 1 Ω |
| r7-1 (NE+) or C152-28 (NE+) - Body ground and other terminals | Always | 10 kΩ or higher |
| r7-2 (NE-) or C152-19 (NE-) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the crankshaft position sensor connector.
OK
NG
Disconnect the crankshaft position sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C152-20 (VCNE) - C152-28 (NE+) | Engine switch off | No short or no open circuit |
| C152-28 (NE+) - C152-19 (NE-) | Engine switch off | No short or no open circuit |
| *a | Component with harness connected
(ECM) |
Reconnect the crankshaft position sensor connector.
OK
NG
Replace the crankshaft position sensor (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) for 4 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output.
NEXT