Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.



DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Depress and release brake pedal with engine switch on (IG) Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Engine switch on (IG).
(b) Brake pedal is released.
(c) STP signal is OFF when the ST1- signal is OFF.
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A413253E01
0.979,3.615 1.896,3.813 0.917,0.198 10 false 70A FL 0.479,1.531 1.396,1.729 0.917,0.198 10 false ALT 2.302,0.677 3.219,0.875 0.917,0.198 10 false STOP 0.479,2.542 1.396,2.74 0.917,0.198 10 false 250A FL 2.854,1.385 3.771,1.583 0.917,0.198 10 false IGN 4.167,1.844 5.083,2.042 0.917,0.198 10 false A99 4.156,2 5.365,2.26 1.208,0.26 10 false Stop Light Switch 5.583,4.427 6.5,4.625 0.917,0.198 10 false G213 5.583,4.583 6.698,5.188 1.115,0.604 10 false Certification ECU (Smart Key ECU Assembly) 2.708,4.802 4.531,5.052 1.823,0.25 10 false No. 1 Integration Relay 3.573,4.26 3.885,4.458 0.313,0.198 10 false IG2 2.01,3.469 2.323,3.667 0.313,0.198 10 false 1S 2.063,3.302 2.375,3.5 0.313,0.198 10 false 1 2.042,3.844 2.354,4.042 0.313,0.198 10 false 4 2.719,3.625 3.031,3.823 0.313,0.198 10 false IG2 1.99,4.031 2.302,4.229 0.313,0.198 10 false 1W 4.646,4.021 4.958,4.219 0.313,0.198 10 false 1V 4.396,3.188 4.708,3.385 0.313,0.198 10 false 1V 4.208,3.208 4.479,3.427 0.271,0.219 10 false 1 4.677,3.833 4.833,4.031 0.156,0.198 10 false 2 5.49,3.906 5.646,4.104 0.156,0.198 10 false 3 4.917,0.396 5.073,0.594 0.156,0.198 10 false 3 4.083,0.406 4.354,0.625 0.271,0.219 10 false 7 4.917,1.094 5.229,1.292 0.313,0.198 10 false 5 4.083,1.115 4.396,1.313 0.313,0.198 10 false 6 4.094,1.469 4.25,1.667 0.156,0.198 10 false 2 4.271,1.573 5.188,1.771 0.917,0.198 10 false GND 4.281,1.229 5.198,1.427 0.917,0.198 10 false B 4.292,0.51 5.208,0.708 0.917,0.198 10 false B 4.708,0.521 5.625,0.719 0.917,0.198 10 false L 4.729,1.229 5.646,1.427 0.917,0.198 10 false L 5.802,0.417 6.115,0.615 0.313,0.198 10 false 13 5.813,1.115 6.125,1.313 0.313,0.198 10 false 12 6.052,0.406 6.969,0.604 0.917,0.198 10 false STP 6.063,1.104 6.979,1.302 0.917,0.198 10 false ST1- 6.229,2.396 7.146,2.594 0.917,0.198 10 false ECM 6.229,2.208 7.146,2.406 0.917,0.198 10 false G185 5.74,4.031 6.656,4.229 0.917,0.198 10 false IG1D 0.698,4.979 2.521,5.229 1.823,0.25 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

(e)

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY (B VOLTAGE)
E270270E12
0.26,1.042 0.646,1.333 0.385,0.292 2.698,1.75 2.365,1.219 true 2.063,1.219 1.719,1.844 true 0.323,1.115 0.635,1.313 0.313,0.198 10 false A99 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 2.719,1.781 3.031,1.979 0.313,0.198 10 false B 1.677,1.865 1.833,2.063 0.156,0.198 10 false B

a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-7 (B) - Body ground Always 11 to 14 V
A85-6 (B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO.1 INTEGRATION RELAY, BATTERY)

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω



OK

3.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (STP AND ST1- VOLTAGE)
U169492E02
3.063,3.135 3.063,3.979 false 3.031,3.135 2.177,3.979 false 0.271,0.396 0.469,0.563 0.198,0.167 10 false *a 1.698,0.396 1.896,0.563 0.198,0.167 10 false *b 0.219,2.302 0.417,2.469 0.198,0.167 10 false *c 2.781,2.479 3.188,2.635 0.406,0.156 10 false G185 1.615,4 2.229,4.146 0.615,0.146 10 false 13 (STP) 2.646,4 3.26,4.146 0.615,0.146 10 false 12 (ST1)

a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake pedal condition Specified Condition
G185-12 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
G185-13 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V


Text in Illustration
*a Depressed
*b Released
*c Rear view of wire harness connector
(to ECM)



OK

NG

4.CHECK HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A99-3 (L) - G185-13 (STP) Always Below 1 Ω
A99-5 (L) - G180-12 (ST1-) Always Below 1 Ω
A99-3 (L) or G185-13 (STP) - Body ground and other terminals Always 10 kΩ or higher
A99-5 (L) or G185-12 (ST1- ) - Body ground and other terminals Always 10 kΩ or higher



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR