Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P052F  Glow Plug Control Module System Voltage  P0683  Glow Plug Control Module to PCM Communication Circuit  


DESCRIPTION

The glow system consists of the glow plug controller, glow plugs and ECM. The glow plug controller turns on the glow plug of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plugs can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.

The glow plugs are turned on during PM forced regeneration in order to prevent the engine speed from rising due to an increase in fuel injection volume used to increase the exhaust gas temperature. The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.

P052F
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plugs are on (2 trip detection logic). Glow plug controller

P0683
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Enter check mode When the glow plugs are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (2 trip detection logic).
·

Open or short circuit in ground wire

·

Open or short circuit in battery wire

·

Open in SI wire

·

SI wire short circuit to ground or battery

·

Open in DI wire

·

DI wire short circuit to ground or battery

·

Low battery voltage

·

Glow plug controller

·

ECM



WIRING DIAGRAM

A413240E01
1.375,0.51 1.688,0.708 0.313,0.198 10 false SI 1.375,0.917 1.688,1.115 0.313,0.198 10 false DI 1.26,1.344 1.573,1.542 0.313,0.198 10 false GL1 1.25,1.75 1.563,1.948 0.313,0.198 10 false GL2 1.25,2.188 1.563,2.385 0.313,0.198 10 false GL3 1.25,2.604 1.563,2.802 0.313,0.198 10 false GL4 1.615,0.521 1.927,0.719 0.313,0.198 10 false A83 1.615,0.927 1.927,1.125 0.313,0.198 10 false A83 1.604,1.354 1.917,1.552 0.313,0.198 10 false A82 1.615,1.771 1.927,1.969 0.313,0.198 10 false A82 1.615,2.188 1.927,2.385 0.313,0.198 10 false A92 1.615,2.604 1.927,2.802 0.313,0.198 10 false A92 1.344,3.479 1.656,3.677 0.313,0.198 10 false +B 1.167,3.927 1.583,4.125 0.417,0.198 10 false BATT 1.219,4.406 1.531,4.604 0.313,0.198 10 false GND 1.604,4.406 1.917,4.604 0.313,0.198 10 false A83 1.615,3.948 1.927,4.146 0.313,0.198 10 false A80 1.604,3.479 1.917,3.677 0.313,0.198 10 false A83 3.24,2.854 3.635,3.052 0.396,0.198 10 false C165 3.229,3 4.833,3.198 1.604,0.198 10 false Glow Plug Assembly 3.302,1.344 3.813,1.563 0.51,0.219 10 false GLW1 3.302,1.76 3.813,1.979 0.51,0.219 10 false GLW2 3.302,2.167 3.813,2.385 0.51,0.219 10 false GLW3 3.302,2.604 3.813,2.823 0.51,0.219 10 false GLW4 3.167,4.625 3.906,4.854 0.74,0.229 10 false GLOW 5.729,0.531 6.344,0.729 0.615,0.198 10 false C150 5.729,4.302 6.344,4.5 0.615,0.198 10 false G184 5.729,7.594 6.344,7.792 0.615,0.198 10 false G184 4.917,5.146 5.531,5.344 0.615,0.198 10 false EFI NO. 2 3.427,6.792 4.438,6.99 1.01,0.198 10 false EFI MAIN No.2 3.438,7.896 4.448,8.094 1.01,0.198 10 false EFI MAIN No.1 2.75,7.365 3.76,7.563 1.01,0.198 10 false EFI MAIN No.1 2.74,6.229 3.75,6.427 1.01,0.198 10 false EFI MAIN No.2 4.573,6.75 5.26,7.188 0.688,0.438 10 false EFI MAIN No.3 0.896,6.26 1.51,6.458 0.615,0.198 10 false 70A FL 0.865,5.625 1.479,5.823 0.615,0.198 10 false 250A FL 0.563,4.823 1.979,5.094 1.417,0.271 10 false Glow Plug Controller 0.688,7.896 1.698,8.094 1.01,0.198 10 false Battery 3.094,1.229 3.271,1.448 0.177,0.219 10 false 1 3.104,1.646 3.281,1.865 0.177,0.219 10 false 2 3.104,2.052 3.281,2.271 0.177,0.219 10 false 3 3.115,2.469 3.292,2.688 0.177,0.219 10 false 4 1.677,2.406 1.854,2.625 0.177,0.219 10 false 2 1.688,1.99 1.865,2.208 0.177,0.219 10 false 1 1.688,1.583 1.865,1.802 0.177,0.219 10 false 2 1.688,1.146 1.865,1.365 0.177,0.219 10 false 1 1.677,0.729 1.854,0.948 0.177,0.219 10 false 5 1.698,0.313 1.875,0.531 0.177,0.219 10 false 3 1.698,3.271 1.875,3.49 0.177,0.219 10 false 4 1.677,3.729 1.854,3.948 0.177,0.219 10 false 1 1.677,4.188 1.854,4.406 0.177,0.219 10 false 1 5.74,0.938 6.354,1.135 0.615,0.198 10 false C150 5.813,0.302 5.99,0.521 0.177,0.219 10 false 11 5.823,0.729 6,0.948 0.177,0.219 10 false 10 5.802,7.385 5.979,7.604 0.177,0.219 10 false 14 5.823,4.073 6,4.292 0.177,0.219 10 false 15 1.979,7.583 2.292,7.781 0.313,0.198 10 false 1W 5.208,5.917 5.521,6.115 0.313,0.198 10 false 3 5.146,6.104 5.458,6.302 0.313,0.198 10 false 1W 5.208,7.406 5.521,7.604 0.313,0.198 10 false 8 5.146,7.583 5.458,7.781 0.313,0.198 10 false 1W 2.042,7.406 2.354,7.604 0.313,0.198 10 false 4 2,6.094 2.313,6.292 0.313,0.198 10 false 1S 2.031,5.906 2.344,6.104 0.313,0.198 10 false 1 6.146,7.604 6.615,7.865 0.469,0.26 10 false MREL 6.156,4.302 6.625,4.563 0.469,0.26 10 false GREL 6.156,0.927 6.625,1.188 0.469,0.26 10 false GLDI 6.156,0.542 6.625,0.802 0.469,0.26 10 false GLDO 4.302,4.917 4.917,5.115 0.615,0.198 10 false GLOW

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0683 is output A
DTC P052F is output B



A

2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)

B

12.REPLACE GLOW PLUG CONTROLLER
2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)
a.
U169374E02
1.792,1.188 2.073,1.729 true 0.208,0.063 0.365,0.229 0.156,0.167 10 false *a 2.021,1.729 2.24,1.927 0.219,0.198 10 false +B 0.708,1.083 0.99,1.26 0.281,0.177 10 false A83

Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A83-4 (+B) - Body ground Engine switch ON 11 to 14 V
A83-4 (+B) - Body ground Engine switch off Below 0.5 V


Text in Illustration
*a Front view of wire harness connector
(to Glow Plug Controller)


c.

Reconnect the glow plug controller connector.



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)
a.
U169375E02
1.5,1.188 1.177,1.677 true 0.208,0.063 0.365,0.229 0.156,0.167 10 false *a 0.917,1.698 1.271,1.896 0.354,0.198 10 false GND 0.698,1.083 0.979,1.26 0.281,0.177 10 false A83

Disconnect the glow plug controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A83-1 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the glow plug controller connector.



OK

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
a.

Disconnect the glow plug controller connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A83-3 (SI) - C150-11 (GLDO) Always Below 1 Ω
A83-5 (DI) - C150-10 (GLDI) Always Below 1 Ω
A83-3 (SI) or C150-11 (GLDO) - Body ground and other terminals Always 10 kΩ or higher
A83-5 (DI) or C150-10 (GLDI) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the glow plug controller connector.


e.

Reconnect the ECM connector.



OK

8.REPLACE GLOW PLUG CONTROLLER

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 INTEGRATION RELAY)
a.

Disconnect the glow plug controller connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A83-4 (+B) - 1W-3 Always Below 1 Ω
A83-4 (+B) or 1W-3 - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 integration relay



OK

6.CHECK CHARGING SYSTEM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK CHARGING SYSTEM
a.

Check the charging system and perform repairs as necessary (See page Power Source / Network>1GD-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller (See page Engine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG CONTROLLER>REMOVAL).



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


g.

Read the DTCs.

OK:

No DTC is output.


HINT:

Check for DTCs in check mode.




OK

END

NG

10.REPLACE ECM
10.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


g.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.




NEXT

END

12.REPLACE GLOW PLUG CONTROLLER
a.


NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


g.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.




NEXT

END