Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

P0617
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

ST relay circuit

·

Park/neutral position switch assembly*1

·

Clutch start switch*2

·

ECM



*1: for Automatic Transmission

*2: for Manual Transmission

Related Data List
DTC No. Data List
P0617 Starter Signal

WIRING DIAGRAM

for Automatic Transmission:

A356522E03
0.563,2.51 0.917,2.688 0.354,0.177 10 false STA 4.938,3.771 5.156,3.948 0.219,0.177 10 false ST 2.948,3.24 3.271,3.417 0.323,0.177 10 false ST 6.479,3.073 6.885,3.24 0.406,0.167 10 false ECM 6.344,0.698 6.896,0.875 0.552,0.177 10 false NSW 6.479,2.917 6.948,3.104 0.469,0.188 10 false G184 3.156,1.292 3.708,1.479 0.552,0.188 10 false C159 6.083,0.24 6.323,0.427 0.24,0.188 10 false 23 4.146,4.167 4.292,4.354 0.146,0.188 10 false 3 4.771,4.167 4.917,4.354 0.146,0.188 10 false 1 4.771,3.406 4.917,3.594 0.146,0.188 10 false 2 3,5.313 3.25,5.531 0.25,0.219 10 false 1*1 3.406,5.313 3.688,5.51 0.281,0.198 10 false 1*2 6.073,2.396 6.271,2.594 0.198,0.198 10 false 22 4.802,1.24 5.167,1.417 0.365,0.177 10 false B 3.156,1.479 4.563,1.979 1.406,0.5 10 false Park/Neutral Position Switch Assembly 0.917,0.26 1.25,0.427 0.333,0.167 10 false 14 4.146,3.396 4.281,3.563 0.135,0.167 10 false 5 0.917,0.604 1.198,0.781 0.281,0.177 10 false 10 6.344,2.51 6.854,2.688 0.51,0.177 10 false STA 6.083,0.594 6.302,0.781 0.219,0.188 10 false 11 2.229,5.917 2.74,6.083 0.51,0.167 10 false Battery 3.708,6.115 4.885,6.281 1.177,0.167 10 false Starter Assembly 4.167,4.958 4.573,5.146 0.406,0.188 10 false D11 0.646,0.344 1.01,0.521 0.365,0.177 10 false NE 0.458,0.698 0.979,0.875 0.521,0.177 10 false STAR 0.927,2.417 1.25,2.594 0.323,0.177 10 false 12 6.354,0.333 6.792,0.51 0.438,0.177 10 false NEO 5.031,5.865 6.365,6.042 1.333,0.177 10 false *1: for 2.0 kW type 5.031,6.188 6.396,6.365 1.365,0.177 10 false *2: for 2.7 kW type 3.021,5.531 3.271,5.719 0.25,0.188 10 false D8 4.802,1.896 5.167,2.073 0.365,0.177 10 false L 4.531,5.177 4.844,5.385 0.313,0.208 10 false 1*2 4.531,4.948 4.865,5.146 0.333,0.198 10 false 1*1 4.156,5.198 4.563,5.385 0.406,0.188 10 false D10 3.427,5.531 3.677,5.719 0.25,0.188 10 false D9 0.24,2.917 0.656,3.094 0.417,0.177 10 false G213 4.76,1.042 5.125,1.219 0.365,0.177 10 false 4 4.76,2.104 5.125,2.281 0.365,0.177 10 false 5 0.24,3.083 1.885,3.531 1.646,0.448 10 false Certification ECU (Smart Key ECU Assembly)

for Manual Transmission:

A362189E03
0.542,2.521 0.896,2.698 0.354,0.177 10 false STA 4.927,3.771 5.146,3.948 0.219,0.177 10 false ST 2.948,3.24 3.271,3.417 0.323,0.177 10 false ST 6.5,3.083 6.906,3.25 0.406,0.167 10 false ECM 6.469,2.917 6.938,3.104 0.469,0.188 10 false G184 3.146,1.292 4.042,1.479 0.896,0.188 10 false A40*1, r1*2 6.083,0.229 6.323,0.417 0.24,0.188 10 false 23 4.135,4.167 4.281,4.354 0.146,0.188 10 false 3 4.76,4.167 4.906,4.354 0.146,0.188 10 false 1 4.76,3.396 4.906,3.583 0.146,0.188 10 false 2 2.99,5.333 3.323,5.521 0.333,0.188 10 false 1*3 3.396,5.323 3.75,5.51 0.354,0.188 10 false 1*4 6.063,2.396 6.26,2.594 0.198,0.198 10 false 22 4.792,1.031 5.156,1.208 0.365,0.177 10 false 2 3.146,1.479 4.552,1.979 1.406,0.5 10 false Cluch Start Switch Assembly 0.917,0.208 1.25,0.375 0.333,0.167 10 false 14 4.135,3.406 4.271,3.573 0.135,0.167 10 false 5 0.917,0.563 1.198,0.74 0.281,0.177 10 false 10 6.333,2.531 6.844,2.708 0.51,0.177 10 false STA 2.229,5.917 2.74,6.083 0.51,0.167 10 false Battery 3.698,6.115 4.875,6.281 1.177,0.167 10 false Starter Assembly 4.156,4.969 4.563,5.156 0.406,0.188 10 false D11 5.021,5.219 5.833,5.396 0.813,0.177 10 false *1: for LHD 5.021,5.552 5.917,5.729 0.896,0.177 10 false *2: for RHD 0.635,0.354 1,0.531 0.365,0.177 10 false NE 0.448,0.719 0.969,0.896 0.521,0.177 10 false STAR 0.917,2.396 1.49,2.563 0.573,0.167 10 false 12 6.344,0.344 6.781,0.521 0.438,0.177 10 false NEO 5.021,5.865 6.375,6.042 1.354,0.177 10 false *3: for 2.0 kW type 5.021,6.188 7,6.365 1.979,0.177 10 false *4: for 2.7 kW type 3.01,5.531 3.26,5.719 0.25,0.188 10 false D8 4.792,2.125 5.156,2.302 0.365,0.177 10 false 1 4.156,5.188 4.563,5.375 0.406,0.188 10 false D10 3.427,5.531 3.677,5.719 0.25,0.188 10 false D9 0.219,2.875 0.573,3.052 0.354,0.177 10 false G213 0.219,3.052 1.76,3.635 1.542,0.583 10 false Certification ECU (Smart Key ECU Assembly) 4.521,4.969 4.854,5.156 0.333,0.188 10 false 1*3 4.51,5.167 4.865,5.354 0.354,0.188 10 false 1*4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page ).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE

PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON (for Automatic Transmission) B
ON (for Manual Transmission) C




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

4.INSPECT CLUTCH START SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).



OK

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and wait for at least 30 seconds.


d.

Turn the engine switch on (IG).


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B




A

7.CHECK ENTRY AND START SYSTEM (START FUNCTION)

B

END

7.CHECK ENTRY AND START SYSTEM (START FUNCTION)

OK

END

NG

REPAIR OR REPLACE ENTRY AND START SYSTEM