Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE) › from 2017.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260781 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) J

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  Pattern Select Switch Sport Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and sport shift patterns and lock-up pattern.

By following the programs corresponding to the signals from the SPORT mode switch (eco mode switch (drive mode)), the park/neutral position switch and other various sensors, the ECM switches the solenoid valves on and off, and controls the transmission gear change and the lock-up clutch operation.

WIRING DIAGRAM

C386001E01
6.385,0.552 7,0.75 0.615,0.198 10 false 12 V 6.396,1.5 7.01,1.698 0.615,0.198 10 false 12 V 5.073,1.844 5.531,2.042 0.458,0.198 10 false G55 5.063,0.906 5.521,1.104 0.458,0.198 10 false G56 5.51,0.781 6.125,0.979 0.615,0.198 10 false SPCN 5.521,1.708 6.135,1.906 0.615,0.198 10 false PWMS 5.125,1.615 5.438,1.813 0.313,0.198 10 false 18 5.156,0.667 5.313,0.865 0.156,0.198 10 false 7 4.167,0.792 4.479,0.99 0.313,0.198 10 false 13 3.844,0.792 4,0.99 0.156,0.198 10 false B 3.052,0.802 3.208,1 0.156,0.198 10 false 7 2.25,0.792 3.167,0.99 0.917,0.198 10 false NORMAL 2.365,1.719 3.135,1.917 0.771,0.198 10 false SPORT 3.052,1.719 3.208,1.917 0.156,0.198 10 false 3 4.167,1.719 4.479,1.917 0.313,0.198 10 false 15 3.844,1.719 4,1.917 0.156,0.198 10 false P 2.521,2.344 2.979,2.542 0.458,0.198 10 false GND 3.052,2.344 3.208,2.542 0.156,0.198 10 false 5 3.844,2.333 4,2.531 0.156,0.198 10 false E 4.167,2.333 4.479,2.531 0.313,0.198 10 false 18 5.906,2.469 6.365,2.667 0.458,0.198 10 false ECM 2.969,2.927 3.583,3.125 0.615,0.198 10 false G303 2.969,3.094 6.635,3.292 3.667,0.198 10 false Shift Position Indicator 1.427,2.948 2.531,3.385 1.104,0.438 10 false Eco Mode Switch (Drive Mode)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - BODY GROUND)
a.
C384711E01
1.458,0.156 1.948,0.458 0.49,0.302 2.802,1.844 2.177,1.406 true 1.542,0.24 2.156,0.438 0.615,0.198 10 false G303 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 2.875,1.823 3.031,2.021 0.156,0.198 10 false E

Disconnect the shift position indicator connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G303-18 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Shift Position Indicator)



OK

2.CHECK SHIFT POSITION INDICATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK SHIFT POSITION INDICATOR
a.
C384710E01
1.896,1.448 2.656,1.698 true 2.188,1.375 2.698,0.99 true 0.75,1.802 1.26,1.417 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 2.76,1.615 3.073,1.813 0.313,0.198 10 false P 2.792,0.885 2.948,1.083 0.156,0.198 10 false B 0.615,1.792 0.771,1.99 0.156,0.198 10 false E

Disconnect the shift position indicator connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
15 (P) - 18 (E) SPORT mode switch pushed and held Below 10 Ω
SPORT mode switch not pushed 10 kΩ or higher
13 (B) - 18 (E) NORMAL mode switch pushed and held Below 10 Ω
NORMAL mode switch not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Shift Position Indicator)



OK

3.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - ECM)

NG

4.INSPECT ECO MODE SWITCH (DRIVE MODE)
3.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - ECM)
a.
C386002E01
0.281,0.25 0.698,0.49 0.417,0.24 0.771,0.25 1.188,0.49 0.417,0.24 2.271,2.167 2.76,2.74 true 1.469,3.094 1.156,2.479 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.365,0.292 0.823,0.49 0.458,0.198 10 false G55 0.844,0.292 1.302,0.49 0.458,0.198 10 false G56 1.208,3.156 2.125,3.385 0.917,0.229 10 false 18 (PWMS) 2.563,2.792 3.302,3.042 0.74,0.25 10 false 7 (SPCN)

Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G55-18 (PWMS) - Body ground SPORT mode switch pushed and held Below 10 Ω
SPORT mode switch not pushed 10 kΩ or higher
G56-7 (SPCN) - Body ground NORMAL mode switch pushed and held Below 10 Ω
NORMAL mode switch not pushed 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ECO MODE SWITCH (DRIVE MODE)
a.
C380111E01
0.656,1.094 1.146,1.094 true 2.021,1.448 2.542,1.875 true 1.792,1 2.427,0.24 true 0.083,0.083 0.333,0.323 0.25,0.24 10 false *1 2.51,0.146 3.375,0.344 0.865,0.198 10 false SPORT 0.333,1.031 0.646,1.24 0.313,0.208 10 false GND 2.646,1.875 3.292,2.042 0.646,0.167 10 false NORMAL

Remove the eco mode switch (drive mode) connector (See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (SPORT) - 5 (GND) SPORT mode switch pushed and held Below 10 Ω
SPORT mode switch not pushed 10 kΩ or higher
7 (NORMAL) - 5 (GND) NORMAL mode switch pushed and held Below 10 Ω
NORMAL mode switch not pushed 10 kΩ or higher


Text in Illustration
*1 Eco Mode Switch (Drive Mode)



OK

NG