Refer to DTC P2120 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2120).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 5 seconds or more.
·
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %. ·
Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal. |
Either of the following conditions is met (1 trip detection logic):
1.
Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V. (learned value of accelerator off position) 2.
Difference between VPA and VPA2 is greater than or equal to the specified value. |
·
Accelerator pedal sensor assembly ·
ECM |
| DTC No. | Data List |
|---|---|
| P2121 | ·
Accel Position ·
Accel Sens. No.1 Volt % ·
Accel Sens. No.2 Volt % |
Refer to DTC P2120 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2120).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
NG
OK
Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Wait for 5 seconds after turning the engine switch on (IG).
Turn the GTS on.
Operate the accelerator pedal in accordance with the following procedure [B].
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.
Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2121 is output | A |
| No DTC is output | B |
A
B
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Wait for 5 seconds after turning the engine switch on (IG).
Turn the GTS on.
Operate the accelerator pedal in accordance with the following procedure [B].
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.
Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT