Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P2141  Diesel Throttle Motor Circuit Low  P2142  Diesel Throttle Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the diesel throttle body assembly.

P2141
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 5 seconds or more Both of the following conditions are met for 2.0 seconds (1 trip detection logic):
(1 trip detection logic)
·

The throttle actuator duty cycle is 80% or higher.

·

The throttle actuator current is less than 0.5 A.


·

Open or short in throttle actuator circuit

·

Diesel throttle body assembly

·

ECM



P2142
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 5 seconds or more A throttle actuator current of 8 A or higher or the ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic)
·

Open or short in throttle actuator circuit

·

Diesel throttle body assembly

·

ECM



Related Data List
DTC No. Data List
P2141
P2142
Throttle Motor DUTY

WIRING DIAGRAM

A348546E12
0.208,2.531 0.521,2.729 0.313,0.198 10 false r5 0.208,2.719 2.604,3.125 2.396,0.406 10 false Throttle Actuator (Built into Diesel Throttle Body Assembly) 1.458,1.365 1.771,1.563 0.313,0.198 10 false 2 1.469,2.094 1.781,2.292 0.313,0.198 10 false 1 4.906,1.125 5.219,1.323 0.313,0.198 10 false M+ 4.917,1.865 5.229,2.063 0.313,0.198 10 false M- 5.552,1.167 6.688,1.563 1.135,0.396 10 false Throttle Actuator Control Circuit 4.667,1.354 4.979,1.552 0.313,0.198 10 false 6 4.688,2.104 5,2.302 0.313,0.198 10 false 5 5.271,3.146 5.99,3.375 0.719,0.229 10 false C152 5.292,3.333 5.74,3.531 0.448,0.198 10 false ECM 1.146,1.125 1.458,1.323 0.313,0.198 10 false M+ 1.146,1.854 1.458,2.052 0.313,0.198 10 false M-

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT DIESEL THROTTLE BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Remove the diesel throttle body assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL


b.
A327312E05
0.135,0.125 0.448,0.281 0.313,0.156 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always No short or no open circuit



*a Component without harness connected
(Diesel Throttle Body Assembly)


OK

2.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r5-2 (M+) - C152-6 (M+) Always Below 1 Ω
r5-1 (M-) - C152-5 (M-) Always Below 1 Ω
r5-2 (M+) or C152-6 (M+) - Body ground and other terminals Always 10 kΩ or higher
r5-1 (M-) or C152-5 (M-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the diesel throttle body assembly connector.



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

NEXT

5.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

5.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for 30 seconds.


f.

Start the engine.


g.

Idle the engine for 5 seconds or more.


h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.



NEXT

END