Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A348993E01
1.125,2.385 0.677,1.354 0.677,1.354 0.844,1.354 true 1.271,1.813 1.427,1.198 1.427,1.198 1.573,1.198 true 1.229,3.104 1.49,3.594 1.49,3.594 1.615,3.594 true 0.063,2.74 0.615,3.135 0.552,0.396 10 false Sensor Vane 0.313,3.906 2.604,4.427 2.292,0.521 10 false Nozzle Vane Position Sensor (Turbocharger Nozzle Vane Control Actuator) 1.625,1.135 2.281,1.354 0.656,0.219 10 false Magnet 1.854,1.469 2.344,1.656 0.49,0.188 10 false VNVC 2.844,3.552 3.354,3.75 0.51,0.198 10 false ECM 4.219,1.656 4.688,1.854 0.469,0.198 10 false 4.65 3.531,0.677 5.333,1.094 1.802,0.417 10 false Nozzle Vane Position Sensor Output Voltage (V) 1.906,2.25 2.396,2.438 0.49,0.188 10 false VTA1 1.896,3.021 2.385,3.208 0.49,0.188 10 false VNE2 2.75,1.583 3.24,1.771 0.49,0.188 10 false VNVC 2.75,2.375 3.24,2.563 0.49,0.188 10 false VNA 2.729,3.167 3.219,3.354 0.49,0.188 10 false VNE2 1.656,3.521 2.313,3.74 0.656,0.219 10 false Magnet 0.896,1.281 1.479,1.479 0.583,0.198 10 false Hall IC 4.229,2.823 4.698,3.021 0.469,0.198 10 false 0.35 6.042,3.354 6.74,3.615 0.698,0.26 10 false Open 4.917,3.354 5.531,3.594 0.615,0.24 10 false Closed 5.021,3.76 6.615,4 1.594,0.24 10 false Nozzle Vane Position

P2564
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 2 seconds or more VNA voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger nozzle vane control actuator)

·

Open or short in nozzle vane position sensor circuit

·

ECM



P2565
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 2 seconds or more VNA voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger nozzle vane control actuator)

·

Open or short in nozzle vane position sensor circuit

·

ECM



HINT:

If DTC P2564 and/or P2565 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

- Lack of power

- Vehicle surge or hesitation under light or medium load



WIRING DIAGRAM

A348545E01
0.615,2.646 1.073,2.844 0.458,0.198 10 false C144 0.615,2.854 3.406,3.292 2.792,0.438 10 false Nozzle Vane Position Sensor (Turbocharger Nozzle Vane Control Actuator) 5.771,2.625 6.229,2.823 0.458,0.198 10 false C151 5.781,2.802 6.24,3 0.458,0.198 10 false ECM 5.458,1.833 5.917,2.031 0.458,0.198 10 false VNE2 5.448,1.375 5.906,1.573 0.458,0.198 10 false VNA 5.448,0.896 5.969,1.094 0.521,0.198 10 false VNVC 5.188,1.125 5.646,1.323 0.458,0.198 10 false 30 5.198,1.604 5.656,1.802 0.458,0.198 10 false 23 5.198,2.063 5.656,2.26 0.458,0.198 10 false 22 1.677,1.021 2.198,1.219 0.521,0.198 10 false VNVC 1.708,1.49 2.167,1.688 0.458,0.198 10 false VTA1 1.688,1.948 2.146,2.146 0.458,0.198 10 false VNE2 2.177,1.146 2.635,1.344 0.458,0.198 10 false 1 2.188,1.625 2.646,1.823 0.458,0.198 10 false 3 2.188,2.063 2.646,2.26 0.458,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)
a.
U169887E01
0.615,1.018 0.980,1.195 0.366,0.177 10 C144 1.012,1.57 1.536,1.724 0.524,0.154 10 VNVC 0.093,0.058 0.311,0.213 0.218,0.154 10 *a 2.053,1.587 2.545,1.741 0.492,0.154 10 VNE2 1.772,1.241 2.043,1.57 false

Disconnect the nozzle vane position sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C144-1 (VNVC) - C144-2 (VNE2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Nozzle Vane Position Sensor)


d.

Reconnect the nozzle vane position sensor connector.



OK

2.INSPECT NOZZLE VANE POSITION SENSOR (VNA VOLTAGE)

NG

6.CHECK ECM (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)
2.INSPECT NOZZLE VANE POSITION SENSOR (VNA VOLTAGE)
a.
U169400E01
1.448,1.635 1.125,2.417 false 1.49,1.635 1.875,2.396 false 0.135,0.01 0.406,0.219 0.271,0.208 10 false *a 1.333,0.906 1.75,1.063 0.417,0.156 10 false C151 0.563,2.448 1.208,2.635 0.646,0.188 10 false 23 (VNA) 1.792,2.448 2.573,2.604 0.781,0.156 10 false 22 (VNE2)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C151-23 (VNA) - C151-22 (VNE2) Engine switch on (IG) 2.3 to 2.7 V


Text in Illustration
*a Component with harness connected
(ECM)



NG

3.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - ECM)

OK

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - ECM)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C144-3 (VTA1) - C151-23 (VNA) Always Below 1 Ω
C144-2 (VNE2) - C151-22 (VNE2) Always Below 1 Ω
C144-3 (VTA1) or C151-23 (VNA) - Body ground and other terminals Always 10 kΩ or higher
C144-2 (VNE2) or C151-22 (VNE2) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the nozzle vane position sensor connector.


e.

Reconnect the ECM connector.



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (CHECK RESISTANCE)
a.
U169888E01
0.615,1.018 0.980,1.195 0.366,0.177 10 C144 0.892,1.724 1.416,1.879 0.524,0.154 10 VNVC 0.093,0.058 0.311,0.213 0.218,0.154 10 *a 1.744,1.724 2.236,1.879 0.492,0.154 10 VNE2 1.772,1.241 1.888,1.707 false 2.491,1.724 2.983,1.879 0.492,0.154 10 VTA1 2.013,1.252 2.481,1.707 false

Disconnect the nozzle vane position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C144-1 (VNVC) - C144-3 (VTA1) Engine switch off No short or open circuit
C144-3 (VTA1) - C144-2 (VNE2)


Text in Illustration
*a Front view of wire harness connector
(to Nozzle Vane Position Sensor)


c.

Reconnect the nozzle vane position sensor connector.



OK

5.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR (NOZZLE VANE POSITION SENSOR)

NG

7.REPLACE ECM
5.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR (NOZZLE VANE POSITION SENSOR)
a.

Replace the turbocharger nozzle vane control actuator (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY).



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK ECM (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)
a.
U169401E01
1.448,1.688 1.125,2.417 false 1.49,1.635 1.875,2.396 false 0.135,0.01 0.406,0.219 0.271,0.208 10 false *a 1.333,0.896 1.75,1.052 0.417,0.156 10 false C151 0.594,2.448 1.354,2.635 0.76,0.188 10 false 30 (VNVC) 1.844,2.438 2.625,2.594 0.781,0.156 10 false 22 (VNE2)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C151-30 (VNVC) - C151-22 (VNE2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

7.REPLACE ECM
7.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and wait for 30 seconds or more.


d.

Turn the engine switch on (IG) for 2 seconds or more.


e.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P2564 and/or P2565.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.




NEXT

END