When the engine switch is turned on (IG), the battery voltage is applied to terminal IGSW of the ECM. The MREL output signal from ECM causes a current to flow to the coil, closing the contacts of the EFI MAIN1 relay and supplying power to terminal +B, +B2 and +B3 of the ECM.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G185-2 (+B) - C152-1 (E1) | Engine switch on (IG) | 11 to 14 V |
| G185-3 (+B2) - C152-1 (E1) | Engine switch on (IG) | 11 to 14 V |
| G185-4 (+B3) - C152-1 (E1) | Engine switch on (IG) | 11 to 14 V |
| *a | Component with harness connected
(ECM) |
NG
OK
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C152-1 (E1) - Body ground | Always | Below 1 Ω |
Reconnect the ECM connector.
OK
NG
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G185-18 (IGSW) - C152-1 (E1) | Engine switch on (IG) | 11 to 14 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G184-14 (MREL) - C152-1 (E1) | Engine switch on (IG) | 11 to 14 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Inspect the No. 1 integration relay (EFI MAIN1) (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/o Urea SCR System)>ON-VEHICLE INSPECTION).
OK
NG
Remove the No. 1 integration relay from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1W-8 - G184-14 (MREL) | Always | Below 1 Ω |
| 1W-10 - G185-2 (+B) | Always | Below 1 Ω |
| 1W-10 - G185-3 (+B2) | Always | Below 1 Ω |
| 1W-10 - G185-4 (+B3) | Always | Below 1 Ω |
| 1W-4 - Body ground | Always | Below 1 Ω |
| 1W-8 - G184-14 (MREL) - Body ground and other terminals | Always | Below 1 Ω |
| 1W-10 or G185-2 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| 1W-10 or G185-3 (+B2) - Body ground and other terminals | Always | 10 kΩ or higher |
| 1W-10 or G185-4 (+B3) - Body ground and other terminals | Always | 10 kΩ or higher |
Reinstall the No. 1 integration relay.
Reconnect the ECM connector.
OK
NG
Inspect the No. 1 integration relay (IG2 relay) (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/o Urea SCR System)>ON-VEHICLE INSPECTION).
OK
NG
Remove the No. 1 integration relay from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1V-1 - G185-18 (IGSW) | Always | Below 1 Ω |
| 1W-4 - Body ground | Always | Below 1 Ω |
| 1V-1 or G185-18 (IGSW) - Body ground and other terminals | Always | 10 kΩ or higher |
Reinstall the No. 1 integration relay.
Reconnect the ECM connector.
OK
NG
Remove the No. 1 integration relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1S-1 - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to No. 1 Integration Relay) |
Reinstall the No. 1 integration relay.
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connector.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G213-8 (IG1D) - 1V-2 | Always | Below 1 Ω |
| G213-8 (IG1D) or 1V-2 - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the certification ECU (smart key ECU assembly) connector.
Reinstall the No. 1 integration relay.
OK
NG