Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the electric EGR control valve assembly and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.

P0405
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 2 seconds or more EGR valve position sensor output voltage is less than 0.2 V for 2 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

Electric EGR control valve assembly (EGR valve position sensor)

·

ECM



P0406
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 2 seconds or more EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

Electric EGR control valve assembly (EGR valve position sensor)

·

ECM



MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.2 to 4.8 V for more than 2 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ECM (EGR VALVE POSITION SENSOR VOLTAGE)
a.
U169395E01
1.323,1.698 0.927,2.406 false 1.406,1.635 2.073,2.406 false 1.344,0.927 1.729,1.083 0.385,0.156 10 false C151 1.76,2.458 2.51,2.615 0.75,0.156 10 false 24 (EEGL) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 0.573,2.458 1.406,2.615 0.833,0.156 10 false 31 (VCEG)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C151-31 (VCEG) - C151-24 (EEGL) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

2.INSPECT EGR VALVE POSITION SENSOR (EGLS VOLTAGE)

NG

9.REPLACE ECM
2.INSPECT EGR VALVE POSITION SENSOR (EGLS VOLTAGE)
a.
U169396E01
1.365,1.635 0.917,2.448 false 1.417,1.646 2.083,2.417 false 1.333,0.938 1.854,1.094 0.521,0.156 10 false C151 1.76,2.458 2.51,2.615 0.75,0.156 10 false 24 (EEGL) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 0.573,2.458 1.281,2.615 0.708,0.156 10 false 25 (EGLS)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C151-25 (EGLS) - C151-24 (EEGL) Engine switch on (IG) 0.6 to 1.4 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

4.CHECK HARNESS AND CONNECTOR
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off.


d.

Turn the engine switch on (IG) for 2 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

4.CHECK HARNESS AND CONNECTOR
a.
U169493C01
1.083,1.875 0.656,2.552 false 1.708,1.885 2.042,2.552 false 0.104,0.083 0.323,0.281 0.219,0.198 10 false *a 1.615,0.667 2.063,0.823 0.448,0.156 10 false C127 0.552,2.583 0.844,2.75 0.292,0.167 10 false E2 1.927,2.583 2.219,2.75 0.292,0.167 10 false VC

Disconnect the electric EGR control valve assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C127-3 (VC) - C127-1 (E2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Electric EGR control valve assembly)


c.

Reconnect the electric EGR control valve assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C127-3 (VC) - C151-31 (VCEG) Always Below 1 Ω
C127-2 (VTA) - C151-25 (EGLS) Always Below 1 Ω
C127-1 (E2) - C151-24 (EEGL) Always Below 1 Ω
C127-3 (VC) or C151-31 (VCEG) - Body ground and other terminals Always 10 kΩ or higher
C127-2 (VTA) or C151-25 (EGLS) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the electric EGR control valve assembly connector.


e.

Reconnect the ECM connector.



OK

6.CHECK ECM (CHECK RESISTANCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM (CHECK RESISTANCE)
a.
U169494E01
1.083,1.875 0.656,2.552 false 1.708,1.885 2.042,2.552 false 1.396,1.885 1.396,2.552 false 0.104,0.083 0.323,0.281 0.219,0.198 10 false *a 1.604,0.646 2.01,0.802 0.406,0.156 10 false C127 0.552,2.583 0.844,2.75 0.292,0.167 10 false E2 1.927,2.583 2.219,2.75 0.292,0.167 10 false VC 1.229,2.583 1.563,2.75 0.333,0.167 10 false VTA

Disconnect the electric EGR control valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C127-3 (VC) - C127-2 (VTA) Engine switch off No short or open
C127-2 (VTA) - C127-1 (E2)


Text in Illustration
*a Front view of wire harness connector
(to Electric EGR control valve assembly)


c.

Reconnect the electric EGR control valve assembly connector.



OK

7.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

9.REPLACE ECM
7.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch on (IG) for 2 seconds or more.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END