Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  


DESCRIPTION

The ECM opens and closes the throttle valve using a DC motor type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

Although the DTC title says "Exhaust Gas Recirculation Throttle Position Control Range / Performance", this DTC indicates that the throttle valve is malfunctioning.

P0488
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. The throttle actuator activation duty is more than specified value for 60 seconds.
(1 trip detection logic)
·

Throttle valve stuck

·

Throttle valve does not move smoothly

·

Open or short in throttle control motor circuit

·

ECM



Related Data List
DTC No. Data List
P0488
·

Target Throttle Position

·

Actual Throttle Position

·

Throttle Motor Duty

·

Throttle Close Learning Val.



Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the DC motor with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

A128641E35
4.625,2.135 4.75,1.813 false 4.604,2.896 4.729,2.573 false 4.615,3.635 4.74,3.323 false 4.74,4.104 4.615,3.792 false 5.344,5.271 5.167,5.052 false 3.344,5.365 3.104,5.188 false 0.292,5.427 1.688,5.792 1.396,0.365 10 false Duty Ratio Malfunction Counter 0.135,0.031 1.917,0.24 1.781,0.208 10 false Malfunction Detection: 0.292,1.24 1.698,1.604 1.406,0.365 10 false Throttle Valve Target Opening Angle 0.292,2.708 1.771,3.104 1.479,0.396 10 false Throttle Valve Actual Opening Angle 0.948,4.115 1.688,4.333 0.74,0.219 10 false Duty Ratio 4.802,1.708 5.396,1.906 0.594,0.198 10 false Normal 4.802,2.479 5.552,2.677 0.75,0.198 10 false Abnormal 4.802,3.979 5.396,4.177 0.594,0.198 10 false Normal 4.802,3.219 5.552,3.417 0.75,0.198 10 false Abnormal 5.948,0.552 6.396,0.75 0.448,0.198 10 false Open 5.948,1.302 6.427,1.5 0.479,0.198 10 false Close 5.948,2.021 6.396,2.219 0.448,0.198 10 false Open 5.948,2.771 6.427,2.969 0.479,0.198 10 false Close 5.948,3.521 6.458,3.719 0.51,0.198 10 false 100% 5.948,4.281 6.292,4.479 0.344,0.198 10 false 0% 3.375,5.302 4.792,5.51 1.417,0.208 10 false Stores P0488 5.375,5.24 6.167,5.448 0.792,0.208 10 false Threshold 3.51,6.271 3.917,6.469 0.406,0.198 10 false Time

CAUTION / NOTICE / HINT

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / Data List / Primary / Actual Throttle Position.


d.

When changing the Active Test continuously value to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.




OK

2.CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

NG

5.CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
2.CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.





NEXT

3.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
3.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
a.

Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.

OK:

Throttle valve moves smoothly.


NOTICE:

Take care not to damage the throttle valve or valve housing.




OK

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

9.REPLACE DIESEL THROTTLE BODY ASSEMBLY
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Start the engine and warm it up.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Take a snapshot with the GTS.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / Data List / Primary / Actual Throttle Position.

HINT:

The movement of the throttle valve can be determined by performing the following inspection.



f.

When changing the Active Test value continuously to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



g.

Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

OK:

DTC is not output.




OK

END

NG

10.REPLACE ECM
5.CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.





NEXT

6.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
6.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
a.

Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.

OK:

Throttle valve moves smoothly.


NOTICE:

Take care not to damage the throttle valve or valve housing.




OK

7.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)

NG

9.REPLACE DIESEL THROTTLE BODY ASSEMBLY
7.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r5-5 (VC) - C151-29 (VCVL) Always Below 1 Ω
r5-6 (VTA) - C151-21 (VLU) Always Below 1 Ω
r5-3 (E2) - C151-20 (EVLU) Always Below 1 Ω
r5-2 (M+) - C152-6 (M+) Always Below 1 Ω
r5-1 (M-) - C152-5 (M-) Always Below 1 Ω
r5-5 (VC) or C151-29 (VCVL) - Body ground and other terminals Always 10 kΩ or higher
r5-6 (VTA) or C151-21 (VLU) - Body ground and other terminals Always 10 kΩ or higher
r5-3 (E2) or C151-20 (EVLU) - Body ground and other terminals Always 10 kΩ or higher
r5-2 (M+) or C152-6 (M+) - Body ground and other terminals Always 10 kΩ or higher
r5-1 (M-) or C152-5 (M-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the throttle control motor connector.


e.

Reconnect the ECM connector.



NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

9.REPLACE DIESEL THROTTLE BODY ASSEMBLY
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS
9.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS
10.REPLACE ECM

NEXT

11.CHECK WHETHER DTC OUTPUT RECURS
11.CHECK WHETHER DTC OUTPUT RECURS
a.

Start the engine and warm it up.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Take a snapshot with the GTS.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / Data List / Primary / Actual Throttle Position.

HINT:

The movement of the throttle valve can be determined by performing the following inspection.



e.

When changing the Active Test value continuously to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



f.

Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output.



NEXT

END