The glow system consists of the glow plug controller, glow plugs and ECM. The glow plug controller turns on the glow plug of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plugs can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.
The glow plugs are turned on during PM forced regeneration in order to prevent the engine speed from rising due to an increase in fuel injection volume used to increase the exhaust gas temperature. The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Enter check mode | The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plugs are on (2 trip detection logic). | Glow plug controller |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Enter check mode | When the glow plugs are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (2 trip detection logic). | ·
Open or short circuit in ground wire ·
Open or short circuit in battery wire ·
Open in SI wire ·
SI wire short circuit to ground or battery ·
Open in DI wire ·
DI wire short circuit to ground or battery ·
Low battery voltage ·
Glow plug controller ·
ECM |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0683 is output | A |
| DTC P052F is output | B |
A
B
Disconnect the glow plug controller connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A83-4 (+B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| A83-4 (+B) - Body ground | Engine switch off | Below 0.5 V |
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
Reconnect the glow plug controller connector.
OK
NG
Disconnect the glow plug controller connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A83-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
Reconnect the glow plug controller connector.
OK
NG
Disconnect the glow plug controller connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A83-3 (SI) - C150-11 (GLDO) | Always | Below 1 Ω |
| A83-5 (DI) - C150-10 (GLDI) | Always | Below 1 Ω |
| A83-3 (SI) or C150-11 (GLDO) - Body ground and other terminals | Always | 10 kΩ or higher |
| A83-5 (DI) or C150-10 (GLDI) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the glow plug controller connector.
Reconnect the ECM connector.
OK
NG
Disconnect the glow plug controller connector.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A83-4 (+B) - 1W-3 | Always | Below 1 Ω |
| A83-4 (+B) or 1W-3 - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the glow plug controller connector.
Reinstall the No. 1 integration relay
OK
NG
Check the charging system and perform repairs as necessary (See page Power Source / Network>1GD-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).
NEXT
Repair or replace the harness or connector.
NEXT
Replace the glow plug controller (See page Engine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG CONTROLLER>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>CHECK MODE PROCEDURE).
Read the DTCs.
No DTC output.
Check for DTCs in check mode.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>CHECK MODE PROCEDURE).
Confirm that the DTC is not output again.
Check for DTCs in check mode.
NEXT
Replace the glow plug controller (See page Engine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG CONTROLLER>REMOVAL)
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>CHECK MODE PROCEDURE).
Confirm that the DTC is not output again.
Check for DTCs in check mode.
NEXT