The urea injector opens the needle valve and injects urea solution according to operation signals sent by the urea pump control ECU.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Reductant Injection Valve (Active Test) | When the urea injector is operating, an open or short circuit occurs in the urea injector circuit for 5 seconds or more.
(1 trip detection logic) |
·
Open or short in urea injector set circuit ·
Urea injector set ·
Urea pump control ECU |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Reductant Injection Valve (Active Test) | When the urea injector is operating, an open or short circuit occurs in the urea injector circuit for 5 seconds or more.
(1 trip detection logic) |
·
Open or short in urea injector set circuit ·
Urea injector set ·
Urea pump control ECU |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the urea injector set (See Page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA INJECTOR>INSPECTION).
OK
NG
| *a | Front view of wire harness connector
(to Urea Injector Set) |
*b | Front view of wire harness connector
(to Urea Pump Control ECU) |
Disconnect the urea injector set connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C168-2 - s4-8 (UIV+) | Always | Below 1 Ω |
| C168-1 - s4-7 (UIV-) | Always | Below 1 Ω |
| C168-2 or s4-8 (UIV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C168-1 or s4-7 (UIV-) - Body ground and other terminals | Always | 10 kΩ or higher |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Injection Valve.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2048 or P2049 is output | A |
| DTCs is not output | B |
A
B
Replace the urea pump control ECU (See pageEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Injection Valve.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT
Repair or replace the harness or connector.
NEXT
Replace the urea injector set (See pageEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL).
NEXT