Refer to DTC P202B (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P202B).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Reductant Pipe Heater (Active Test) | When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more.
(1 trip detection logic) |
·
Open or short in urea tube with heater assembly circuit ·
Urea tube with heater assembly ·
Urea pump control ECU |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Reductant Pipe Heater (Active Test) | When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more.
(1 trip detection logic) |
·
Open or short in urea tube with heater assembly circuit ·
Urea tube with heater assembly ·
Urea pump control ECU |
| DTC No. | Data List |
|---|---|
| P20BB
P20BC |
Reductant Pipe Heater |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the urea tube with heater assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 6.39 to 7.81 Ω |
| *a | Component without harness connected
(to Urea Tube with Heater Assembly) |
OK
NG
| *a | Front view of wire harness connector
(to Urea Tube with Heater Assembly) |
*b | Front view of wire harness connector
(to Urea Pump Control ECU) |
Disconnect the urea tube with heater assembly connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| s2-1(HTUL) - s4-20(HTL) | Always | Below 1 Ω |
| s2-2(GND1) - s4-32(EHTL) | Always | Below 1 Ω |
| s2-1(HTUL) or s4-20(HTL) - Body ground | Always | 10 kΩ or higher |
| s2-2(GND1) or s4-32(EHTL) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off and wait for 30 seconds or more.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Pipe Heater.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P20BB or P20BC is output | A |
| DTCs is not output | B |
A
B
Replace the urea pump control ECU (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off and wait for 30 seconds or more.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Pipe Heater.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT
Repair or replace the harness or connector.
NEXT
Replace the urea tube with heater assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL).
NEXT