Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P202B  Reductant Tank Heater Control Circuit Low  P202C  Reductant Tank Heater Control Circuit High  


DESCRIPTION

An electric heater is provided inside the urea tank and urea pipe, as urea solution freezes at -11°C (12.2°F) or lower.

The heater thaws frozen urea solution and prevents further freezing, allowing the urea SCR system to be started even in cold environments.

The tank heater turns ON and OFF according to the value of the temperature sensor. The heater for the urea tube with heater assembly turns ON and OFF according to the value of the ambient temperature sensor.

P202B
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Reductant Tank Heater (Active Test) When the tank heater is operating, an open or short circuit occurs in the tank heater for 3 seconds or more.
(1 trip detection logic)
·

Open or short in tank heater circuit

·

Tank heater (Urea Pump)

·

Urea pump control ECU



P202C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Reductant Tank Heater (Active Test) When the tank heater is operating, an open or short circuit occurs in the tank heater for 3 seconds or more.
(1 trip detection logic)
·

Open or short in tank heater circuit

·

Tank heater (Urea Pump)

·

Urea pump control ECU



Related Data List
DTC No. Data List
P202B
P202C
Reductant Tank Heater

WIRING DIAGRAM

A357971E07
1.844,1.344 2.302,1.542 0.458,0.198 10 false TH+ 1.875,1.917 2.188,2.115 0.313,0.198 10 false TH- 0.49,2.646 0.802,2.844 0.313,0.198 10 false s3 0.49,2.823 4.01,3.021 3.521,0.198 10 false Tank Heater (Urea Pump) 2.198,1.563 2.354,1.76 0.156,0.198 10 false 9 2.188,2.156 2.5,2.354 0.313,0.198 10 false 11 4.979,1.552 5.292,1.75 0.313,0.198 10 false 21 4.979,2.177 5.292,2.375 0.313,0.198 10 false 31 5.271,1.448 5.729,1.646 0.458,0.198 10 false HTT 5.281,2.063 5.896,2.26 0.615,0.198 10 false EHTT 5.24,2.969 5.552,3.167 0.313,0.198 10 false s4 5.24,3.146 6.896,3.354 1.656,0.208 10 false Urea Pump Control ECU

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT TANK HEATER (UREA PUMP)
a.

Inspect the tank heater (urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>INSPECTION



OK

2.CHECK HARNESS AND CONNECTOR (TANK HEATER (UREA PUMP) - UREA PUMP CONTROL ECU))

NG

9.REPLACE UREA PUMP
2.CHECK HARNESS AND CONNECTOR (TANK HEATER (UREA PUMP) - UREA PUMP CONTROL ECU))
U169576E03
1.969,0.927 1.26,1.375 false 2.219,0.938 2.833,1.323 false 5.167,1.01 4.625,1.479 false 5.271,0.802 5.833,1.469 false 1.708,0.177 1.927,0.385 0.219,0.208 10 false s3 5.448,0.156 5.677,0.344 0.229,0.188 10 false s4 0.198,0.094 0.51,0.292 0.313,0.198 10 false *a 4.24,0.115 4.594,0.385 0.354,0.271 10 false *b 1.063,1.365 1.438,1.51 0.375,0.146 10 false TH- 2.771,1.313 3.271,1.521 0.5,0.208 10 false TH+ 4.031,1.427 4.74,1.635 0.708,0.208 10 false 31(EHTT) 5.885,1.438 6.656,1.656 0.771,0.219 10 false 21(HTT)

Text in Illustration
*a Front view of wire harness connector
(to Tank Heater (urea pump))
*b Front view of wire harness connector
(to Urea Pump Control ECU)

a.

Disconnect the tank heater (urea pump) connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s3-9 (TH+) - s4-21 (HTT) Always Below 1 Ω
s3-11 (TH-) - s4-31 (EHTT) Always Below 1 Ω
s3-9 (TH+) or s4-21 (HTT) - Body ground and other terminals Always 10 kΩ or higher
s3-11 (TH-) or s4-31 (EHTT) - Body ground and other terminals Always 10 kΩ or higher




OK

3.CLEAR DTC

NG

8.REPAIR OR REPLACE HARNESS AND CONNECTOR
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off for 30 seconds or more.



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Tank Heater .


d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.


Result:
Result Proceed to
DTC P202B or P202C is output A
DTCs is not output B



A

5.REPLACE UREA PUMP CONTROL ECU

B

END

5.REPLACE UREA PUMP CONTROL ECU

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off for 30 seconds or more.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Tank Heater.


d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END

8.REPAIR OR REPLACE HARNESS AND CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CLEAR DTC
9.REPLACE UREA PUMP

NEXT

6.CLEAR DTC