Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal position sensor.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted on the accelerator pedal sensor assembly and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal position sensor.

In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0.5 V and 4.8 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.

A255815E26
4.333,2.042 4.208,1.958 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.219,2.333 false 4.333,2.406 4.219,2.521 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.844,2.875 0.552,3.281 false 1.063,2.198 1.323,1.365 false 4.333,1.833 3.844,0.938 false 1.323,1.365 1.417,1.365 false 1.063,2.563 0.927,1.823 false 0.927,1.823 0.854,1.823 false 0.552,3.802 1.708,4.135 1.156,0.333 10 false Accelerator Pedal Position Sensor 1.458,1.292 2.031,1.521 0.573,0.229 10 false Magnet 0.323,1.74 0.854,1.917 0.531,0.177 10 false IC No. 1 0.313,3.354 0.844,3.531 0.531,0.177 10 false IC No. 2 2.063,1.729 2.604,1.958 0.542,0.229 10 false VPA 2.063,2.063 2.542,2.302 0.479,0.24 10 false EPA 2.063,2.385 2.792,2.667 0.729,0.281 10 false VCPA 2.063,2.688 2.438,2.865 0.375,0.177 10 false VPA2 2.063,3 2.438,3.177 0.375,0.177 10 false EPA2 2.063,3.323 2.438,3.5 0.375,0.177 10 false VCP2 2.677,3.76 3,3.938 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.833 4.208,2.01 0.292,0.177 10 false 4.55 3.844,2.042 4.208,2.219 0.365,0.177 10 false 3.988 3.917,2.26 4.208,2.438 0.292,0.177 10 false 3.75 3.854,2.448 4.219,2.625 0.365,0.177 10 false 3.188 3.969,2.823 4.479,3.063 0.51,0.24 10 false 1.6 3.99,3.042 4.656,3.417 0.667,0.375 10 false 0.8 4.406,3.354 4.698,3.531 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.073,3.771 0.292,0.177 10 false 13.1 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.667,3.896 7.167,4.094 2.5,0.198 10 false Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.146,0.813 3.844,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V)

P2120
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V and VPA2 is more than 2.7 deg, or VPA is higher than 4.8 V.
·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2122
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V.
(b) VPA2 is more than 2.7 deg.
·

Accelerator pedal sensor assembly

·

Open in VCPA circuit

·

VPA circuit open or shorted to ground

·

Accelerator pedal rod (arm) deformed

·

ECM



P2123
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Condition (a) continues for 2.0 seconds (1 trip detection logic):
(a) VPA is higher than 4.8 V.
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

Accelerator pedal assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2125
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V and VPA is more than 2.7 deg, or VPA2 is higher than 4.8 V and VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2127
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V.
(b) VPA1 is more than 2.7 deg.
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

VPA2 circuit open or shorted to ground

·

Accelerator pedal rod (arm) deformed

·

ECM



P2128
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) VPA2 is higher than 4.8 V.
(b) VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

Accelerator pedal rod (arm) deformed

·

ECM



P2138
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Conditions (a) or (b) continue for 2.0 seconds (1 trip detection logic):
(a) The difference between VPA and VPA2 is less than 0.02 V.
(b) VPA is below 0.4 V and VPA2 is below 1.2 V.
·

VPA and VPA2 circuits are short-circuited

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



Related Data List
DTC No. Data List
P2120
P2122
P2123
P2125
P2127
P2128
P2138
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %



WIRING DIAGRAM

A348544E09
0.396,3.052 0.854,3.25 0.458,0.198 10 false A19 0.375,3.229 3.177,3.583 2.802,0.354 10 false Accelerator Pedal Position Sensor (Accelerator Pedal Sensor Assembly) 5.906,3.052 6.365,3.25 0.458,0.198 10 false G185 5.917,3.24 6.375,3.438 0.458,0.198 10 false ECM 1.604,0.542 2.063,0.74 0.458,0.198 10 false VPA 1.594,0.969 2.052,1.167 0.458,0.198 10 false EPA 1.51,1.396 2.219,1.615 0.708,0.219 10 false VCPA 1.531,1.802 1.99,2 0.458,0.198 10 false VPA2 1.531,2.219 1.99,2.417 0.458,0.198 10 false EPA2 1.531,2.635 1.99,2.833 0.458,0.198 10 false VCP2 2,2.74 2.458,2.938 0.458,0.198 10 false 1 2,2.333 2.458,2.531 0.458,0.198 10 false 2 2.01,1.927 2.469,2.125 0.458,0.198 10 false 3 2.01,1.479 2.469,1.677 0.458,0.198 10 false 4 2.01,1.083 2.469,1.281 0.458,0.198 10 false 5 1.99,0.656 2.448,0.854 0.458,0.198 10 false 6 5.333,0.646 5.792,0.844 0.458,0.198 10 false 28 5.323,1.073 5.781,1.271 0.458,0.198 10 false 22 5.333,1.5 5.792,1.698 0.458,0.198 10 false 29 5.333,1.917 5.792,2.115 0.458,0.198 10 false 31 5.333,2.333 5.792,2.531 0.458,0.198 10 false 25 5.333,2.75 5.792,2.948 0.458,0.198 10 false 30 5.615,2.521 6.073,2.719 0.458,0.198 10 false VCP2 5.583,2.094 6.042,2.292 0.458,0.198 10 false EPA2 5.594,1.667 6.052,1.865 0.458,0.198 10 false VPA2 5.594,1.229 6.302,1.448 0.708,0.219 10 false VCPA 5.594,0.833 6.052,1.031 0.458,0.198 10 false EPA 5.615,0.417 6.073,0.615 0.458,0.198 10 false VPA

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION)
a.
C129061E03
0.834,1.598 1.046,1.806 0.212,0.208 10 *a 0.266,0.318 0.472,0.524 0.205,0.205 10 *1 2.244,1.598 2.505,1.811 0.261,0.212 10 *b

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.


d.

Read the values.

Standard Voltage:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%


Text in Illustration
*1 Accelerator Pedal Assembly
*a Depressed
*b Released

Result
Result Proceed to
NG A
OK B



A

2.CHECK ECM (ACCELERATOR PEDAL POSITION SENSOR VOLTAGE)

B

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK ECM (ACCELERATOR PEDAL POSITION SENSOR VOLTAGE)
a.
U169397E01
2.823,1.635 1.156,2.479 false 2.875,1.688 2.073,2.479 false 3,1.688 2.99,2.469 false 2.292,0.813 3.042,1.635 false 2.802,0.896 3.208,1.052 0.406,0.156 10 false G185 1.552,0.677 2.26,0.833 0.708,0.156 10 false 22 (EPA) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 0.76,2.49 1.469,2.646 0.708,0.156 10 false 25 (EPA2) 2.563,2.49 3.271,2.646 0.708,0.156 10 false 29 (VCPA) 1.667,2.49 2.375,2.646 0.708,0.156 10 false 30 (VCP2)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G185-29 (VCPA) - G185-22 (EPA) Engine switch on (IG) 4.5 to 5.5 V
G185-30 (VCP2) - G185-25 (EPA2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

3.INSPECT ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY (VPA, VPA2 VOLTAGE)

NG

8.REPLACE ECM
3.INSPECT ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY (VPA, VPA2 VOLTAGE)
a.
U169398E01
2.823,1.635 1.156,2.479 false 2.833,1.688 2.073,2.479 false 3,1.688 2.948,2.469 false 2.292,0.813 3.042,1.635 false 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 2.823,0.917 3.198,1.073 0.375,0.156 10 false G185 1.552,0.677 2.26,0.833 0.708,0.156 10 false 22 (EPA) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 0.76,2.49 1.469,2.646 0.708,0.156 10 false 25 (EPA2) 2.563,2.49 3.271,2.646 0.708,0.156 10 false 28 (VPA) 1.667,2.49 2.375,2.646 0.708,0.156 10 false 31 (VPA2)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G185-28 (VPA) - G185-22 (EPA) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed 0.5 to 1.1 V
C185-31 (VPA2) - G185-25 (EPA2) Engine switch on (IG), accelerator pedal fully released 0.9 to 2.3 V
Engine switch on (IG), accelerator pedal fully depressed 0.9 to 2.3 V


Text in Illustration
*a Component with harness connected
(ECM)



NG

4.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)

OK

8.REPLACE ECM
4.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
a.
U169110E01
1,3.083 1.469,2.448 false 1.302,2.438 0.792,2.823 false 2.031,3.094 1.906,2.448 false 1.771,2.438 1.583,3.094 false 0.177,0.26 0.365,0.563 0.188,0.302 10 false *a 0.396,2.156 0.708,2.406 0.313,0.25 10 false A19 1.938,3.125 2.26,3.292 0.323,0.167 10 false EPA 0.688,3.125 1.073,3.292 0.385,0.167 10 false EPA2 0.292,2.75 0.698,2.917 0.406,0.167 10 false VCP2 1.354,3.104 1.771,3.271 0.417,0.167 10 false VCPA

Disconnect the accelerator pedal sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A19-4 (VCPA) - A19-5 (EPA) Engine switch on (IG) 4.5 to 5.5 V
A19-1 (VCP2) - A19-2 (EPA2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)


c.

Reconnect the accelerator pedal sensor assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-6 (VPA) - G50-28 (VPA) Always Below 1 Ω
A19-5 (EPA) - G185-22 (EPA) Always Below 1 Ω
A19-3 (VPA2) - G185-31 (VPA2) Always Below 1 Ω
A19-2 (EPA2) - G185-25 (EPA2) Always Below 1 Ω
A19-6 (VPA) or G185-28 (VPA) - Body ground and other terminals Always 10 kΩ or higher
A19-5 (EPA) or G185-22 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A19-3 (VPA2) or G185-31 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A19-2 (EPA2) or G185-25 (EPA2) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the accelerator pedal sensor assembly connector.


e.

Reconnect the ECM connector.



OK

6.CHECK ECM (CHECK RESISTANCE)

NG

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK ECM (CHECK RESISTANCE)
a.
U169399E01
2.833,1.635 2.292,0.927 false 2.833,1.698 0.594,2.49 false 3.042,1.698 3.063,2.802 false 2.292,0.49 3.042,1.635 false 3,1.688 2.49,2.469 false 2.875,1.698 1.604,2.51 false 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 2.833,0.917 3.208,1.073 0.375,0.156 10 false G185 1.698,0.417 2.406,0.573 0.708,0.156 10 false 22 (EPA) 0.104,0.094 0.375,0.25 0.271,0.156 10 false *a 1.635,0.844 2.344,1 0.708,0.156 10 false 25 (EPA2) 2.688,2.844 3.302,3 0.615,0.156 10 false 28 (VPA) 0.208,2.51 0.917,2.667 0.708,0.156 10 false 31 (VPA2) 2.01,2.521 2.719,2.677 0.708,0.156 10 false 29 (VCPA) 1.115,2.531 1.823,2.688 0.708,0.156 10 false 30 (VCP2)

Disconnect the accelerator pedal sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G185-29 (VCPA) - G185-28 (VPA) Engine switch off No short or open circuit
G185-28 (VPA) - G185-22 (EPA) Engine switch off No short or open circuit
G185-30 (VCP2) - G185-31 (VPA2) Engine switch off No short or open circuit
G185-31 (VPA2) - G185-25 (EPA2) Engine switch off No short or open circuit


Text in Illustration
*a Component with harness connected
(ECM)


c.

Reconnect the accelerator pedal sensor assembly connector.



OK

7.REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

NG

8.REPLACE ECM
7.REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and leave the vehicle for 30 seconds.


d.

Turn the engine switch on (IG).


e.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END