Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2018.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1)  P2238  Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2239  Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 1 Sensor 1)  P2252  Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2253  Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 1 Sensor 1)  


DESCRIPTION

HINT:

If P2237, P2238, P2239, P2252 and/or P2253 is present, refer to the DTC table for DPF system (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).


Refer to DTC P2120 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P0031).

P2237
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S2" displays 200°C (392°F) or higher using the GTS.


When either of the following conditions is met (1 trip detection logic):
·

An open in the circuit between terminals A1A+ and A1A-, voltage difference between terminals A1A+ and A1A- is 0.1 V or less

·

The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more.


Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2238
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds The A1A+ voltage is 1.0 V or less
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2239
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds The A1A- voltage is 1.0 V or less
(1 trip detection logic)
Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2252
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds Air fuel ratio sensor circuit low (bank 1 sensor 1)
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2253
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds The A1A- voltage is higher than 4.0 V
(1 trip detection logic)
Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



Related Data List
DTC No. Data List
P2237
P2238
P2239
P2252
P2253
·

AFS Voltage B1S1

·

Exhaust Temperature B1S2



MONITOR DESCRIPTION

The air fuel ratio sensor outputs a voltage in proportion to the air-fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C131-3 (A1A+) - C152-31 (A1A+) Always Below 1 Ω
C131-4 (A1A-) - C152-32 (A1A-) Always Below 1 Ω
C131-3 (A1A+) or C152-31 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C131-4 (A1A-) or C152-32 (A1A-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reconnect the ECM connector.



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE AIR FUEL RATIO SENSOR

NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.



e.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S2) is 200°C (392°F) or higher.



f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
DTC P2237, P2238, P2239, P2252 or P2253 is output A
DTCs are not output B



B

END

A

4.REPLACE ECM
4.REPLACE ECM

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.



e.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S2) is 200°C (392°F) or higher.



f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END