The No. 4 exhaust gas temperature sensor is installed after the SCR catalyst to detect the exhaust gas temperature. A thermistor built into the No. 4 exhaust gas temperature sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value. The No. 4 exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage is applied to the No. 4 exhaust gas temperature sensor from terminal THSO via resistor R. Resistor R and the No. 4 exhaust gas temperature sensor are connected in series. When the resistance value of the No. 4 exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminal THSO also changes. The No. 4 exhaust gas temperature sensor monitors the temperature downstream of the SCR catalyst.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine. | No. 4 Exhaust gas temperature sensor output voltage is below 0.11 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·
After starting the engine, 1 minute or more elapses ·
Engine is running ·
Coolant temperature is 70°C (158°F) or higher |
·
Open or short in No. 4 exhaust gas temperature sensor circuit ·
No. 4 exhaust gas temperature sensor ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine. | No. 4 Exhaust gas temperature sensor output voltage is higher than 4.89 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·
After starting the engine, 1 minute or more elapses ·
Engine is running ·
Coolant temperature is 70°C (158°F) or higher |
·
Open or short in No. 4 exhaust gas temperature sensor circuit ·
No. 4 exhaust gas temperature sensor ·
ECM |
| DTC No. | Data List |
|---|---|
| P2470
P2471 |
SCR Temperature |
The ECM constantly monitors the output voltages from the No. 4 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.11 V and 4.89 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the No. 4 exhaust gas temperature sensor (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for Rear)>INSPECTION).
OK
NG
Disconnect the No. 4 exhaust gas temperature sensor.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| s5-2 (THSO) - G184-26 (THSO) | Always | Below 1 Ω |
| s5-1 (E2) - G184-33 (ETSO) | Always | Below 1 Ω |
| s5-2 (THSO) or G184-26 (THSO) - Body ground and other terminals | Always | 10 kΩ or higher |
| s5-1 (E2) or G184-33 (ETSO) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the No. 4 exhaust gas temperature sensor.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Replace the No. 4 exhaust gas temperature sensor (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for Rear)>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Start the engine.
Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT