Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), the battery voltage is applied to terminal IGSW of the ECM. The MREL output signal from ECM causes a current to flow to the coil, closing the contacts of the EFI MAIN NO. 1 relay and supplying power to terminal +B, +B2 and +B3 of the ECM.

WIRING DIAGRAM

A356869E04
0.646,4.99 1.156,5.146 0.51,0.156 10 false Battery 2.823,4.167 4.292,4.344 1.469,0.177 10 false No. 1 Integration Relay 2.677,2.927 3.792,3.115 1.115,0.188 10 false EFI MAIN NO. 1 6.417,4.604 6.823,4.802 0.406,0.198 10 false ECM 6.24,1.729 6.521,1.917 0.281,0.188 10 false +B 6.24,3.292 6.76,3.49 0.521,0.198 10 false MREL 6.24,0.604 6.74,0.802 0.5,0.198 10 false IGSW 6.24,4.042 6.469,4.198 0.229,0.156 10 false E1 5.958,3.854 6.156,4.01 0.198,0.156 10 false 1 5.906,3.104 6.104,3.26 0.198,0.156 10 false 14 5.969,2.052 6.135,2.208 0.167,0.156 10 false 3 4.854,0.427 5.021,0.583 0.167,0.156 10 false 1 4.844,0.979 5.01,1.135 0.167,0.156 10 false 4 2.146,0.958 2.313,1.115 0.167,0.156 10 false 2 2.146,3.094 2.313,3.25 0.167,0.156 10 false 4 1.135,1.052 1.302,1.208 0.167,0.156 10 false 3 5.823,0.625 6.24,0.781 0.417,0.156 10 false G185 5.906,0.427 6.146,0.583 0.24,0.156 10 false 18 0.323,1.771 1.417,2.406 1.094,0.635 10 false Certification ECU (Smart Key ECU Assembly) 3.917,1.479 4.281,1.677 0.365,0.198 10 false IG2 3.094,0.74 3.396,0.917 0.302,0.177 10 false IG2 0.708,1.146 1.125,1.323 0.417,0.177 10 false IG1D 0.323,1.604 0.698,1.781 0.375,0.177 10 false G213 0.531,3.656 1.198,3.906 0.667,0.25 10 false 70A FL 2.094,1.156 2.375,1.313 0.281,0.156 10 false 1V 6.24,2.24 6.646,2.427 0.406,0.188 10 false +B2 5.969,1.552 6.146,1.708 0.177,0.156 10 false 2 5.833,1.75 6.25,1.906 0.417,0.156 10 false G185 5.833,2.24 6.25,2.396 0.417,0.156 10 false G185 5.833,2.792 6.25,2.948 0.417,0.156 10 false G185 5.833,3.292 6.25,3.448 0.417,0.156 10 false G184 5.833,4.052 6.25,4.208 0.417,0.156 10 false C152 5.969,2.604 6.135,2.76 0.167,0.156 10 false 4 6.24,2.771 6.656,2.969 0.417,0.198 10 false +B3 4.792,0.625 5.073,0.781 0.281,0.156 10 false 1V 4.781,1.167 5.063,1.323 0.281,0.156 10 false 1W 4.771,2.781 5.052,2.938 0.281,0.156 10 false 1W 4.781,3.292 5.063,3.448 0.281,0.156 10 false 1W 2.094,2.781 2.375,2.938 0.281,0.156 10 false 1S 2.094,3.281 2.375,3.438 0.281,0.156 10 false 1W 4.802,2.594 5.052,2.75 0.25,0.156 10 false 10 4.844,3.104 5.01,3.26 0.167,0.156 10 false 8 2.135,2.594 2.302,2.75 0.167,0.156 10 false 1 5.344,0.75 5.708,1.313 0.365,0.563 10 false IGN NO. 2 3.635,3.667 4.75,3.854 1.115,0.188 10 false EFI MAIN NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (+B, +B2 AND +B3 TERMINAL VOLTAGE)
a.
U169485E03
2.156,1 1.177,1.573 true 3.031,1 1.708,1.521 true 3.083,1.01 2.458,1.542 true 3.156,1 3.073,1.521 true 1.792,0.375 2.208,0.563 0.417,0.188 10 false C152 0.156,0 0.406,0.208 0.25,0.208 10 false *a 2.792,0.365 3.188,0.552 0.396,0.188 10 false G185 0.771,1.542 1.26,1.75 0.49,0.208 10 false 1 (E1) 1.406,1.542 1.938,1.75 0.531,0.208 10 false 4 (+B3) 2.104,1.542 2.635,1.75 0.531,0.208 10 false 3 (+B2) 2.813,1.542 3.271,1.75 0.458,0.208 10 false 2 (+B)

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G185-2 (+B) - C152-1 (E1) Engine switch on (IG) 11 to 14 V
G185-3 (+B2) - C152-1 (E1) Engine switch on (IG) 11 to 14 V
G185-4 (+B3) - C152-1 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

OK

CHECK PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance::
Tester Connection Condition Specified Condition
C152-1 (E1) - Body ground Always Below 1 Ω



c.

Reconnect the ECM connector.



OK

3.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)
a.
U169486E02
2.156,1 1.823,1.521 true 3.219,1.125 2.927,1.521 true 1.813,0.375 2.229,0.563 0.417,0.188 10 false C152 0.156,0 0.406,0.208 0.25,0.208 10 false *a 2.813,0.365 3.208,0.552 0.396,0.188 10 false G185 1.594,1.542 2.083,1.75 0.49,0.208 10 false 1 (E1) 2.458,1.542 3.219,1.75 0.76,0.208 10 false 18 (IGSW)

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G185-18 (IGSW) - C152-1 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

4.CHECK TERMINAL VOLTAGE (MREL TERMINAL VOLTAGE)

NG

7.INSPECT NO. 1 INTEGRATION RELAY (IG2)
4.CHECK TERMINAL VOLTAGE (MREL TERMINAL VOLTAGE)
a.
U169487E02
2.167,1 1.823,1.521 true 2.385,1.063 2.927,1.531 true 1.792,0.375 2.208,0.563 0.417,0.188 10 false C152 0.156,0 0.406,0.208 0.25,0.208 10 false *a 2.354,0.375 2.75,0.563 0.396,0.188 10 false G184 1.563,1.542 2.052,1.75 0.49,0.208 10 false 1 (E1) 2.458,1.542 3.219,1.75 0.76,0.208 10 false 14 (MREL)

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G184-14 (MREL) - C152-1 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

5.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1)
a.

Inspect the No. 1 integration relay (EFI MAIN NO. 1) (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI MAIN1)

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-8 - G184-14 (MREL) Always Below 1 Ω
1W-10 - G185-2 (+B) Always Below 1 Ω
1W-10 - G185-3 (+B2) Always Below 1 Ω
1W-10 - G185-4 (+B3) Always Below 1 Ω
1W-4 - Body ground Always Below 1 Ω
1W-8 or G184-14 (MREL) - Body ground and other terminals Always 10 kΩ or higher
1W-10 or G185-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
1W-10 or G185-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher
1W-10 or G185-4 (+B3) - Body ground and other terminals Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the ECM connector.



OK

9.CHECK TERMINAL VOLTAGE (NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT NO. 1 INTEGRATION RELAY (IG2)
a.


OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2)

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1V-1 - G185-18 (IGSW) Always Below 1 Ω
1W-4 - Body ground Always Below 1 Ω
1V-1 or G185-18 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the ECM connector.



OK

9.CHECK TERMINAL VOLTAGE (NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (NO. 1 INTEGRATION RELAY)
a.
U169115E05
0.583,1.135 0.948,1.323 0.365,0.188 10 false 1S 0.198,0.094 0.448,0.302 0.25,0.208 10 false *a

Remove the No. 1 integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1S-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Integration Relay)


c.

Reinstall the No. 1 integration relay.



OK

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the power management control ECU connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance::
Tester Connection Condition Specified Condition
G213-3 (IG1D) - 1V-2 Always Below 1 Ω
G213-3 (IG1D) or 1V-2 - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the power management control ECU connector.


e.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR