Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The airbag sensor assembly has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123 (malfunction in CAN communication with the yaw rate sensor) and U0124 (malfunction in CAN communication with the acceleration sensor) are stored.

These DTCs are also stored when calibration has not been completed.

DTC C1279 can be cleared when the yaw rate and acceleration sensor (airbag sensor assembly) sends a yaw rate and/or acceleration signal or test mode ends. DTC C1279 is stored only in test mode.

DTC Code DTC Detection Condition Trouble Area
C1232 At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

A/BAG IG2 fuse

·

Acceleration sensor (Airbag sensor assembly)

·

Acceleration sensor (Airbag sensor assembly) circuit


C1243 While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change by 0.0294 G or more occurs 16 times or more.
·

A/BAG IG2 fuse

·

Acceleration sensor (Airbag sensor assembly)

·

Acceleration sensor (Airbag sensor assembly) circuit


C1245 At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

A/BAG IG2 fuse

·

Acceleration sensor (Airbag sensor assembly)

·

Acceleration sensor (Airbag sensor assembly) circuit

·

Sensor installation


C1279 Stored only during test mode.
·

Acceleration sensor (Airbag sensor assembly)

·

Sensor installation



WIRING DIAGRAM

C240027E25
4.99,3.5 6.521,3.896 1.531,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 0.719,4.167 2.396,4.344 1.677,0.177 10 false : CAN Communication Line 2.729,1.917 3.74,2.125 1.01,0.208 10 false A/BAG IG2 0.958,1.75 1.229,1.906 0.271,0.156 10 false IG2 1.271,1.635 1.448,1.792 0.177,0.156 10 false 21 1.271,2.594 1.448,2.75 0.177,0.156 10 false 26 1.271,2.208 1.448,2.365 0.177,0.156 10 false 25 1,2.698 1.198,2.854 0.198,0.156 10 false E2 1,2.333 1.198,2.49 0.198,0.156 10 false E1 0.156,3.563 2.323,3.917 2.167,0.354 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.198,3.313 0.469,3.49 0.271,0.177 10 false G1 4.958,3.302 5.417,3.5 0.458,0.198 10 false A6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly) , perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC U0123, U0124 and/or U0126 is output together with DTC C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by DTC U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>U0073).


PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel and decelerate (depress the brake pedal) the vehicle.


d.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).


e.

Check if DTCs for zero point calibration of the yaw rate and acceleration sensor (C1210) or for zero point calibration of the acceleration sensor (C1336) are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC output (relating to yaw rate and acceleration sensor (airbag sensor assembly)) A
DTC output (relating to CAN communication system) B
DTC (C1210 and/or C1336) output C



A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.




OK

3.CHECK TERMINAL VOLTAGE (IG2, E1, E2)

NG

3.CHECK TERMINAL VOLTAGE (IG2, E1, E2)
NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the G1 yaw rate and acceleration sensor (airbag sensor assembly) connector.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


h.
C233304E23
1.521,0.271 1.969,0.552 0.448,0.281 1.125,1.469 0.563,1.469 false 1.688,1.542 1.479,1.885 false 1.802,1.531 2.021,1.875 false 0.24,1.375 0.49,1.552 0.25,0.177 10 false IG2 0.146,0.073 0.333,0.229 0.188,0.156 10 false *a 1.646,0.333 1.938,0.49 0.292,0.156 10 false G1 1.385,1.885 1.698,2.083 0.313,0.198 10 false E1 1.969,1.875 2.281,2.073 0.313,0.198 10 false E2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-25 (E1) - Body ground Always Below 1 Ω
G1-26 (E2) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))

Result
Result Proceed to
OK (When troubleshooting in accordance with diagnostic trouble code chart) A
OK (When troubleshooting in accordance with problem symptoms table) B
NG C

NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR