Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0329511 THEFT DETERRENT SYSTEM(except 5L-E) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(except 5L-E)  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B341517E14
0.24,0.948 1.052,1.375 0.813,0.427 10 false from Battery 1.448,1.125 2.406,1.354 0.958,0.229 10 false S-HORN 3.052,0.865 3.188,1.052 0.135,0.188 10 false 1 2.052,1.479 2.188,1.667 0.135,0.188 10 false 5 1.906,1.813 3.417,2.281 1.51,0.469 10 false Security Warning Relay (S-HORN) 2.031,0.854 2.167,1.042 0.135,0.188 10 false 2 3.021,1.49 3.156,1.677 0.135,0.188 10 false 3 3.875,0.729 4.177,0.938 0.302,0.208 10 false 27 3.875,0.958 4.177,1.167 0.302,0.208 10 false 2M 5.552,0.969 5.729,1.177 0.177,0.208 10 false A 5.5,0.771 5.719,0.99 0.219,0.219 10 false 29 5.844,0.979 6.156,1.177 0.313,0.198 10 false SH 4.146,1.531 5.802,1.875 1.656,0.344 10 false Driver Side Junction Block Assembly 5.448,3.125 7.094,3.479 1.646,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 2.271,2.76 2.635,2.969 0.365,0.208 10 false A26 2.271,2.948 3.865,3.167 1.594,0.219 10 false Security Horn Assembly 1.917,2.458 2.052,2.646 0.135,0.188 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (Security Horn)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn Security horn assembly ON or OFF -

OK:

The security horn assembly sounds and stops correctly when operated through the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.INSPECT SECURITY WARNING RELAY (S-HORN RELAY)

NG

3.INSPECT SECURITY WARNING RELAY (S-HORN RELAY)
a.
E270109E05
1.948,1.302 2.135,1.302 false 2.698,1.302 2.885,1.302 false 2.542,1.021 2.865,1.021 false 2.552,0.76 2.875,0.76 false 0.458,0.719 0.615,0.917 0.156,0.198 10 false 5 1.271,0.719 1.427,0.917 0.156,0.198 10 false 3 0.458,1.271 0.615,1.469 0.156,0.198 10 false 2 1.26,1.292 1.417,1.49 0.156,0.198 10 false 1 2.927,0.677 3.083,0.875 0.156,0.198 10 false 3 2.917,0.938 3.073,1.135 0.156,0.198 10 false 5 1.854,1.229 2.01,1.427 0.156,0.198 10 false 1 2.938,1.229 3.094,1.427 0.156,0.198 10 false 2

Remove the security warning relay (S-HORN relay).


b.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is applied between terminals 1 - 2 Below 1 Ω
3 - 5 Battery voltage is not applied between terminals 1 - 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SECURITY WARNING RELAY (S-HORN RELAY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE SECURITY WARNING RELAY (S-HORN RELAY)

4.CHECK HARNESS AND CONNECTOR (SECURITY WARNING RELAY (S-HORN RELAY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the driver side junction block assembly connectors.


c.

Remove the security warning relay (S-HORN relay).


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - A-29 (SH) Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
A-29 (SH) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - SECURITY WARNING RELAY (S-HORN RELAY))

NG

7.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (BATTERY - SECURITY WARNING RELAY (S-HORN RELAY))
a.
B341518

Remove the security warning relay (S-HORN relay).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 - Body ground Always 11 to 14 V
5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SECURITY WARNING RELAY (S-HORN RELAY) - SECURITY HORN ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SECURITY WARNING RELAY (S-HORN RELAY) - SECURITY HORN ASSEMBLY AND BODY GROUND)
a.

Remove the security warning relay (S-HORN relay).


b.

Disconnect the A26 security horn assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - A26-1 Always Below 1 Ω
3 - Body ground Always 10 kΩ or higher
A26-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2M driver side junction block assembly connector.


b.

Remove the security warning relay (S-HORN relay).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2M-27 Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
2M-27 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR