Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1282  Center Differential Lock Position Switch  


DESCRIPTION

DTC C1282 is stored only in test mode.

DTC Code DTC Detection Condition Trouble Area
C1282 Stored during test mode.
·

Harness or connector

·

Transfer system

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C212546E12
0.563,0.823 0.75,1.052 0.188,0.229 10 false IG 1.458,1.229 1.667,1.406 0.208,0.177 10 false P1 1.76,1.229 2.031,1.427 0.271,0.198 10 false 3 1.365,4.042 1.625,4.229 0.26,0.188 10 false 2-4 1.396,4.688 1.646,4.875 0.25,0.188 10 false LO 3.292,3.906 3.604,4.104 0.313,0.198 10 false HI 3.281,4.781 3.573,4.969 0.292,0.188 10 false LO 3.24,5.313 4.865,5.51 1.625,0.198 10 false Transfer Position Switch 3.188,2.167 5.208,2.719 2.021,0.552 10 false Center Differential Lock Detection Switch (Transfer Shift Actuator Assembly) 5.219,1.24 5.323,1.396 0.104,0.156 10 false 9 5.438,1.229 5.844,1.438 0.406,0.208 10 false EXI4 5.979,0.667 6.208,0.865 0.229,0.198 10 false IG 5.344,2.49 6.906,2.896 1.563,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 0.135,5.313 2.417,5.583 2.281,0.271 10 false 4 Wheel Drive Control ECU 3.188,1.979 3.5,2.146 0.313,0.167 10 false C43 2.51,2.083 2.854,2.26 0.344,0.177 10 false CDL 2.438,2.521 2.854,2.677 0.417,0.156 10 false GND1 4.479,4.25 4.802,4.438 0.323,0.188 10 false GND 4.875,4.219 5.021,4.375 0.146,0.156 10 false 4 3.063,3.885 3.198,4.042 0.135,0.156 10 false 5 3.063,4.563 3.188,4.719 0.125,0.156 10 false 2 3.24,5.115 3.542,5.323 0.302,0.208 10 false G18 1.76,4.552 1.99,4.719 0.229,0.167 10 false 13 1.771,3.906 1.969,4.073 0.198,0.167 10 false 14 0.135,5.167 0.427,5.313 0.292,0.146 10 false G53 5.333,2.333 5.563,2.51 0.229,0.177 10 false A6 2.906,1.844 3.021,1.99 0.115,0.146 10 false 9 2.917,2.708 3.135,2.865 0.219,0.156 10 false 6 4.281,4.031 4.677,4.208 0.396,0.177 10 false H4F 3.771,4.25 4.229,4.448 0.458,0.198 10 false H4L 4.24,4.771 4.698,4.969 0.458,0.198 10 false L4L

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).


PROCEDURE

1.INSPECT CENTER DIFFERENTIAL LOCK SHIFT
a.

Check that the center differential can shift from free to lock, and from lock to free.

OK:

The center differential can shift from free to lock, and from lock to free.




OK

2.CHECK TEST MODE DTC

NG

3.CHECK TERMINAL VOLTAGE (EXI4)
2.CHECK TEST MODE DTC
a.

Switch the vehicle to test mode, perform the center differential lock signal check, and then check that DTC C1282 is cleared (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>TEST MODE PROCEDURE).

Result
Result Proceed to
DTC is not cleared A
DTC is cleared B



A

B

3.CHECK TERMINAL VOLTAGE (EXI4)
a.

Set the vehicle in the center differential locked state using the center differential lock switch.


b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


d.
U148255E03
2.385,0.188 2.292,0.188 2.292,0.188 2.063,0.844 false 0.281,0.073 0.573,0.271 0.292,0.198 10 false *a 2.406,0.104 2.76,0.271 0.354,0.167 10 false EXI4 0.292,1.01 0.5,1.188 0.208,0.177 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-9 (EXI4) - Body ground Center differential locked
(Center differential lock switch on)
Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


e.

Connect the A6 skid control ECU (brake actuator assembly) connector.


f.

Set the vehicle in the center differential free state using the center differential lock switch.


g.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


h.

Turn the ignition switch to ON.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-9 (EXI4) - Body ground Center differential free
(Center differential lock switch off)
11 to 14 V




OK

4.CHECK TEST MODE DTC

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU/TRANSFER SHIFT ACTUATOR ASSEMBLY)
4.CHECK TEST MODE DTC
a.

Switch the vehicle to test mode, perform the center differential lock signal check, and then check that DTC C1282 is cleared (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>TEST MODE PROCEDURE).

Result
Result Proceed to
DTC is not cleared A
DTC is cleared B



A

B

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU/TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the G53 4 wheel drive control ECU connector.


c.

Disconnect the C43 transfer shift actuator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-9 (EXI4) - G53-3 (P1) Always Below 1 Ω
A6-9 (EXI4) - C43-9 (CDL) Always Below 1 Ω
A6-9 (EXI4) - Body ground Always 10 kΩ or higher




OK

GO TO TRANSFER SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR