Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Signals from the steering sensor are sent to the skid control ECU (built into the brake actuator assembly) through CAN communication.

DTC Code DTC Detection Condition Trouble Area
C1432 A steering sensor power supply malfunction signal is received from the steering sensor.
·

ECU-B fuse

·

ECU-IG NO. 1 fuse

·

Steering sensor power supply

·

Steering sensor circuit

·

Steering sensor



WIRING DIAGRAM

C200080E50
3.938,0.813 4.792,1.01 0.854,0.198 10 false from Battery 3.927,1.458 5.333,1.646 1.406,0.188 10 false from IG Circuit 0.896,0.802 1.198,0.99 0.302,0.188 10 false BAT 1.01,1.417 1.198,1.583 0.188,0.167 10 false IG 0.875,1.75 1.24,1.938 0.365,0.188 10 false ESS 1.323,0.667 1.563,0.865 0.24,0.198 10 false 5 1.323,1.313 1.542,1.51 0.219,0.198 10 false 4 1.323,1.656 1.5,1.813 0.177,0.156 10 false 1 0.229,2.573 1.344,2.771 1.115,0.198 10 false Steering Sensor 0.865,3.469 2.802,3.667 1.938,0.198 10 false : CAN Communication System 5.51,2.26 7.094,2.656 1.583,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 5.51,2.073 6.469,2.271 0.958,0.198 10 false A6 0.229,2.375 0.646,2.552 0.417,0.177 10 false G205 2.073,1.604 3.01,1.771 0.938,0.167 10 false ECU-IG NO. 1 2.25,0.958 2.729,1.146 0.479,0.188 10 false ECU-B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1432, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>U0073).

·

When the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering sensor.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BAT)
a.

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking parts and connecting parts of the connectors.


c.

Disconnect the G205 steering sensor connector.


d.
C266564E04
0.406,1.167 0.823,1.417 0.417,0.25 2.885,1.5 2.167,1.417 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.427,1.208 0.813,1.479 0.385,0.271 10 false G205 2.927,1.458 3.292,1.615 0.365,0.156 10 false BAT

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G205-5 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)



OK

2.CHECK TERMINAL VOLTAGE (IG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IG)
a.

Disconnect the G205 steering sensor connector.


b.
C266564E05
0.333,1.167 0.802,1.417 0.469,0.25 1.875,1.479 1.635,1.938 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.427,1.208 0.813,1.479 0.385,0.271 10 false G205 1.521,1.948 1.74,2.115 0.219,0.167 10 false IG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G205-4 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (ESS CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ESS CIRCUIT)
a.

Disconnect the G205 steering sensor connector.


b.
C266564E07
0.333,1.167 0.802,1.417 0.469,0.25 1.302,1.479 1.063,1.938 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.427,1.208 0.813,1.479 0.385,0.271 10 false G205 0.948,1.958 1.323,2.146 0.375,0.188 10 false ESS

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G205-1 (ESS) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR