Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication assembly.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

EBD operation is not possible.

·

The voltage at terminal IG1 is high.


WIRING DIAGRAM

C386878E02
0.49,4.417 1.104,4.615 0.615,0.198 10 false G304 0.458,4.604 4.438,4.802 3.979,0.198 10 false Combination Meter Assembly 1.323,3.146 1.635,3.344 0.313,0.198 10 false IG 1.104,2.635 1.875,2.833 0.771,0.198 10 false Brake 1.531,2.135 1.844,2.333 0.313,0.198 10 false SW 0.844,1.344 1.302,1.542 0.458,0.198 10 false CPU 0.625,5.146 4.604,5.344 3.979,0.198 10 false : CAN Communication System 1.927,2.021 2.24,2.219 0.313,0.198 10 false 16 2.646,2.021 2.802,2.219 0.156,0.198 10 false 1 2.885,2.031 3.042,2.229 0.156,0.198 10 false + 3.906,2.01 4.063,2.208 0.156,0.198 10 false E 4.135,2.021 4.292,2.219 0.156,0.198 10 false 2 1.99,2.573 4.5,3.031 2.51,0.458 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservor Assenmbly) 2.031,2.385 2.49,2.583 0.458,0.198 10 false A44 4.646,3.677 6.479,3.875 1.833,0.198 10 false ECU-IG NO. 1 5.948,3.51 6.406,3.708 0.458,0.198 10 false IG1 5.604,3.281 5.917,3.479 0.313,0.198 10 false 34 3.354,3.438 5.802,3.635 2.448,0.198 10 false from IG Circuit 5.417,4.563 5.729,4.76 0.313,0.198 10 false A6 5.938,4.104 6.552,4.302 0.615,0.198 10 false GND1 5.688,3.958 5.844,4.156 0.156,0.198 10 false 1 5.427,4.781 6.938,5.135 1.51,0.354 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK TERMINAL VOLTAGE (IG1)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG1)

OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

5.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

5.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.

Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A44 brake fluid level warning switch (brake master cylinder reservor assenmbly) connector.


d.
C219276E04
1.469,1.292 0.698,0.875 false 2,1.281 2.49,0.823 false 0.188,0.156 0.417,0.313 0.229,0.156 10 false *a 2.583,0.74 2.74,0.938 0.156,0.198 10 false + 0.51,0.75 0.667,0.948 0.156,0.198 10 false E

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (E) Switch off (Float up) 10 kΩ or higher
Switch on (Float down) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservor Assenmbly))

HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.




OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Disconnect the G304 combination meter connector.


b.

Disconnect the A44 brake fluid level warning switch (brake master cylinder reservor assenmbly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G304-16 (SW) - A44-1 (+) Always Below 1 Ω
G304-16 (SW) or A44-1 (+) - Body ground Always 10 kΩ or higher
A44-2 (E) - Body ground Always Below 1 Ω




OK

7.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light / ON or OFF OFF -


f.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DATA LIST / ACTIVE TEST).


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B


A

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)