Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (housed in the brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.

The DTC is cleared when the IG1 terminal voltage returns to normal.

DTC Code DTC Detection Condition Trouble Area
C1241 One of the following conditions is met:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is below 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains on and the IG1 terminal voltage is below 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the IG1 terminal voltage at 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.

4.

When the motor fail-safe relay is on after the motor relay turns on, the IG1 terminal voltage is 9.5 V or less and the actuator pump drive motor is off for 0.12 seconds or more.


·

ECU-IG NO. 1 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C194309E50
0.99,1.073 2.021,1.26 1.031,0.188 10 false from IG Circuit 2.896,1.24 3.813,1.427 0.917,0.188 10 false ECU-IG NO. 1 5.24,1.094 5.698,1.292 0.458,0.198 10 false IG1 4.927,0.927 5.208,1.115 0.281,0.188 10 false 34 5.24,1.458 5.698,1.656 0.458,0.198 10 false GND1 5.01,1.302 5.219,1.49 0.208,0.188 10 false 1 5.115,2.677 5.313,2.854 0.198,0.177 10 false A6 5.104,2.844 6.646,3.24 1.542,0.396 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG1)
a.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


b.
U148254E03
2.094,1.99 2.177,1.99 2.177,1.99 2.302,1.396 true 0.281,0.042 0.573,0.24 0.292,0.198 10 false *a 1.844,1.906 2.125,2.073 0.281,0.167 10 false IG1 0.26,1.01 0.51,1.198 0.25,0.188 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-34 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
a.

Reconnect the A6 skid control ECU (brake actuator assembly) connector.



c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC not output A
DTC output B



A

B