Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (ACC)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (ACC) but does change to on (IG)
Power Source Control
·

Power Supply Condition

·

ACC Relay Monitor



WIRING DIAGRAM

B492207E01
4.417,1.771 6.854,1.969 2.438,0.198 10 false Driver Side Junction Block Assembly 1.406,0.771 2.177,0.969 0.771,0.198 10 false SMART 0.115,0.583 1.198,0.781 1.083,0.198 10 false from Battery 2.01,1.927 3.552,2.281 1.542,0.354 10 false Certification ECU (Smart Key ECU Assembly) 2,1.75 2.615,1.948 0.615,0.198 10 false G215 2.292,0.604 2.604,0.802 0.313,0.198 10 false +B 2.313,1.25 2.625,1.448 0.313,0.198 10 false E 2.604,0.969 3.052,1.167 0.448,0.198 10 false ACCD 3.115,0.885 3.271,1.083 0.156,0.198 10 false 9 2.01,0.5 2.323,0.698 0.313,0.198 10 false 10 2.021,1.146 2.333,1.344 0.313,0.198 10 false 11 4.344,0.573 4.656,0.771 0.313,0.198 10 false 2K 4.354,0.99 4.667,1.188 0.313,0.198 10 false 2O 6.479,0.573 6.792,0.771 0.313,0.198 10 false 2O 6.49,0.99 6.802,1.188 0.313,0.198 10 false 2N 5.042,1.302 5.5,1.5 0.458,0.198 10 false ACC 5.802,0.719 6.26,0.917 0.458,0.198 10 false ACC 4.385,0.375 4.542,0.573 0.156,0.198 10 false 1 4.354,0.792 4.667,0.99 0.313,0.198 10 false 23 6.479,0.375 6.792,0.573 0.313,0.198 10 false 50 6.51,0.792 6.667,0.99 0.156,0.198 10 false 1 3.177,0.552 4.26,0.75 1.083,0.198 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start, Power Source Control / Trouble Codes.



Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
C277841C37
1.417,0.094 1.802,0.323 0.385,0.229 0.99,1.698 0.99,0.813 true 0.104,0.052 0.302,0.219 0.198,0.167 10 false *a 0.865,1.74 1.26,1.885 0.396,0.146 10 false ACCD 1.438,0.125 1.906,0.323 0.469,0.198 10 false G215
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G215-9 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)
a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 2O, 2K and 2N driver side junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-9 (ACCD) - 2O-23 Always Below 1 Ω
2N-1 - Body ground Always Below 1 Ω
G215-9 (ACCD) or 2O-23 - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2K-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the all driver side junction block assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

B492526C01
3.021,0.896 3.354,1.083 0.333,0.188 4.573,0.896 4.906,1.083 0.333,0.188 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 3.094,0.906 3.427,1.083 0.333,0.177 10 false 2A 4.635,0.906 4.969,1.083 0.333,0.177 10 false 2D
*a Component with harness connected
(Driver Side Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
2O-50 - Body ground Engine switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY