Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. The ECM continues operating fail-safe mode until a pass condition is detected.


A202104E06
0.117,0.354 1.324,0.510 1.207,0.156 10 (Thermistor) 0.099,0.205 1.491,0.398 1.392,0.193 10 Temperature Sensor 1.416,0.284 1.542,0.284 1.542,0.284 1.954,1.495 false 2.695,0.887 4.434,1.061 1.739,0.174 10 Platinum Hot Wire (Heater) 2.294,1.469 2.63,0.957 false 2.228,0.564 3.333,0.720 1.105,0.156 10 Power Transistor 2.887,1.578 3.846,1.750 0.959,0.172 10 Output Voltage 3.078,2.213 4.817,2.387 1.739,0.174 10 Platinum Hot Wire (Heater) 4.847,1.307 4.447,2.176 false 5.12,1.543 5.586,2.134 false 1.654,1.511 1.800,1.667 0.147,0.156 10 A 2.48,1.512 2.627,1.682 0.147,0.170 10 B 5.245,2.302 6.452,2.458 1.207,0.156 10 (Thermistor) 5.226,2.152 6.618,2.345 1.392,0.193 10 Temperature Sensor

DTC No. DTC Detection Condition Trouble Area
P0102 The mass air flow meter voltage is below 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


P0103 The mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM



HINT:

When any of these DTCs are output, check the airflow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Airflow Rate (gm/sec.) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


160.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.

Example:

When the sensor output voltage remains below 0.2 V, or higher than 4.9 V, for more than 3 seconds, the ECM stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

WIRING DIAGRAM

for Automatic Transmission
A412527E01
5.365,1.208 5.823,1.406 0.458,0.198 10 false C34 5.458,1.01 5.771,1.208 0.313,0.198 10 false 14 5.771,1.094 6.083,1.292 0.313,0.198 10 false VG 5.385,1.708 5.844,1.906 0.458,0.198 10 false C35 5.76,1.604 6.219,1.802 0.458,0.198 10 false E2G 5.458,1.521 5.771,1.719 0.313,0.198 10 false 18 4.74,1.115 5.052,1.313 0.313,0.198 10 false VG 4.729,1.583 5.188,1.781 0.458,0.198 10 false E2G 5.083,1.094 5.24,1.292 0.156,0.198 10 false 5 5.094,1.583 5.25,1.781 0.156,0.198 10 false 4 3.865,0.781 4.177,0.979 0.313,0.198 10 false +B 3.688,0.76 3.844,0.958 0.156,0.198 10 false 3 3.792,2.083 4.25,2.281 0.458,0.198 10 false C33 3.802,2.26 6.708,2.458 2.906,0.198 10 false Mass Air Flow Meter 3.063,1.031 4.438,1.229 1.375,0.198 10 false EFI NO. 2 2.49,0.896 2.802,1.094 0.313,0.198 10 false 1W 2.5,1.24 2.813,1.438 0.313,0.198 10 false 1W 2.573,0.698 2.885,0.896 0.313,0.198 10 false 10 2.594,1.063 2.75,1.26 0.156,0.198 10 false 8 1.594,1.583 3.74,1.781 2.146,0.198 10 false EFI MAIN NO. 1 0.583,1.063 2.729,1.26 2.146,0.198 10 false EFI MAIN NO. 1 1.344,1.958 1.656,2.156 0.313,0.198 10 false 1W 1.156,1.948 1.313,2.146 0.156,0.198 10 false 4 0.365,1.958 0.677,2.156 0.313,0.198 10 false 1S 0.167,1.938 0.323,2.135 0.156,0.198 10 false 1 1.552,2.208 5.073,2.406 3.521,0.198 10 false No. 1 Integration Relay 0.552,2.635 1.104,2.844 0.552,0.208 10 false 70A FL 0.708,3.708 1.781,3.906 1.073,0.198 10 false Battery 5.375,2.979 5.833,3.177 0.458,0.198 10 false G56 5.458,2.781 5.771,2.979 0.313,0.198 10 false 36 5.75,2.875 6.365,3.073 0.615,0.198 10 false MREL 6.083,3.458 6.542,3.656 0.458,0.198 10 false ECM


for Manual Transmission
A412527E03
5.365,1.208 5.823,1.406 0.458,0.198 10 false C35 5.458,1.01 5.771,1.208 0.313,0.198 10 false 14 5.771,1.094 6.083,1.292 0.313,0.198 10 false VG 5.385,1.708 5.844,1.906 0.458,0.198 10 false C35 5.76,1.604 6.219,1.802 0.458,0.198 10 false E2G 5.458,1.521 5.771,1.719 0.313,0.198 10 false 13 4.74,1.115 5.052,1.313 0.313,0.198 10 false VG 4.729,1.583 5.188,1.781 0.458,0.198 10 false E2G 5.083,1.094 5.24,1.292 0.156,0.198 10 false 5 5.094,1.583 5.25,1.781 0.156,0.198 10 false 4 3.865,0.781 4.177,0.979 0.313,0.198 10 false +B 3.688,0.76 3.844,0.958 0.156,0.198 10 false 3 3.792,2.083 4.25,2.281 0.458,0.198 10 false C33 3.802,2.26 6.708,2.458 2.906,0.198 10 false Mass Air Flow Meter 3.063,1.031 4.438,1.229 1.375,0.198 10 false EFI NO. 2 2.49,0.896 2.802,1.094 0.313,0.198 10 false 1W 2.5,1.24 2.813,1.438 0.313,0.198 10 false 1W 2.573,0.698 2.885,0.896 0.313,0.198 10 false 10 2.594,1.063 2.75,1.26 0.156,0.198 10 false 8 1.594,1.583 3.74,1.781 2.146,0.198 10 false EFI MAIN NO. 1 0.583,1.063 2.729,1.26 2.146,0.198 10 false EFI MAIN NO. 1 1.344,1.958 1.656,2.156 0.313,0.198 10 false 1W 1.156,1.948 1.313,2.146 0.156,0.198 10 false 4 0.365,1.958 0.677,2.156 0.313,0.198 10 false 1S 0.167,1.938 0.323,2.135 0.156,0.198 10 false 1 1.552,2.208 5.073,2.406 3.521,0.198 10 false No. 1 Integration Relay 0.552,2.635 1.104,2.854 0.552,0.219 10 false 70A FL 0.708,3.708 1.781,3.906 1.073,0.198 10 false Battery 5.375,2.979 5.833,3.177 0.458,0.198 10 false G55 5.5,2.781 5.813,2.979 0.313,0.198 10 false 9 5.75,2.875 6.365,3.073 0.615,0.198 10 false MREL 6.083,3.458 6.542,3.656 0.458,0.198 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.


e.

Read the values displayed on the GTS.

Result
Mass Airflow Rate (gm/sec.) Proceed to
0.0 A
160.0 or more B
Between 1.0 and 160.0* C

HINT:

*: The value must change when the throttle valve is open or closed with the engine running.




A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

B

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

C

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
U147486E02
1.74,1.406 2.521,0.938 false 0.292,1.344 0.594,1.51 0.302,0.167 10 false C33 0.125,0.104 0.292,0.271 0.167,0.167 10 false *a 2.573,0.802 3.115,1.042 0.542,0.24 10 false +B (+)

a.

Disconnect the mass air flow meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C33-3 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter)


c.

Reconnect the mass air flow meter connector.



OK

3.INSPECT MASS AIR FLOW METER

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
3.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C33-5 (VG) - C34-14 (VG) Always Below 1 Ω
C33-4 (E2G) - C35-18 (E2G) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C33-5 (VG) - C35-14 (VG) Always Below 1 Ω
C33-4 (E2G) - C35-13 (E2G) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C33-5 (VG) or C34-14 (VG) - Body ground Always 10 kΩ or higher
C33-4 (E2G) or C35-18 (E2G) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C33-5 (VG) or C35-14 (VG) - Body ground Always 10 kΩ or higher
C33-4 (E2G) or C35-13 (E2G) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C33-3 (+B) - 1W-10 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C33-3 (+B) or 1W-10 - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-4 (E2G) - Body ground Always Below 1 Ω



c.

Reconnect the mass air flow meter connector.

HINT:

for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).





OK

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C33-4 (E2G) - C35-18 (E2G) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C33-4 (E2G) - C35-13 (E2G) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C33-4 (E2G) or C35-18 (E2G) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C33-4 (E2G) or C35-13 (E2G) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR