Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of this pulse signal.

A115899E88
0.417,1.052 1.365,1.552 0.948,0.5 10 false from Wheel Speed Sensor 1.813,1.958 3.26,2.229 1.448,0.271 10 false Skid Control ECU 3.729,1.958 5.125,2.198 1.396,0.24 10 false Combination Meter 3.115,0.604 3.885,0.875 0.771,0.271 10 false 4-Pulse 5.042,0.604 5.677,0.875 0.635,0.271 10 false 4-Pulse 6.042,1.323 6.51,1.646 0.469,0.323 10 false ECM

DTC No. DTC Detection Condition Trouble Area
P0500 While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM



WIRING DIAGRAM

for Automatic Transmission

A160610E50
0.219,1.802 1.688,1.99 1.469,0.188 10 false from Skid Control ECU 2.167,1.719 2.365,1.885 0.198,0.167 10 false 18 3.917,1.719 4.135,1.885 0.219,0.167 10 false 17 4.948,1.719 5.188,1.885 0.24,0.167 10 false 12 5.969,1.375 6.26,1.542 0.292,0.167 10 false 5 V 5.198,1.938 5.542,2.104 0.344,0.167 10 false SPD 5.729,2.604 6.052,2.771 0.323,0.167 10 false G56 5.729,2.76 6.083,2.927 0.354,0.167 10 false ECM 2.417,1.719 2.615,1.885 0.198,0.167 10 false SI 3.604,1.708 3.854,1.885 0.25,0.177 10 false +S 2.521,2.604 2.958,2.792 0.438,0.188 10 false G304 2.521,2.76 3.729,2.927 1.208,0.167 10 false Combination Meter

for Manual Transmission

A160610E51
0.219,1.802 1.688,1.99 1.469,0.188 10 false from Skid Control ECU 2.167,1.719 2.365,1.885 0.198,0.167 10 false 18 3.917,1.719 4.135,1.885 0.219,0.167 10 false 17 4.948,1.719 5.188,1.885 0.24,0.167 10 false 18 5.969,1.375 6.26,1.542 0.292,0.167 10 false 5 V 5.198,1.938 5.542,2.104 0.344,0.167 10 false SPD 5.729,2.604 6.052,2.771 0.323,0.167 10 false G55 5.729,2.76 6.083,2.927 0.354,0.167 10 false ECM 2.417,1.719 2.615,1.885 0.198,0.167 10 false SI 3.604,1.708 3.854,1.885 0.25,0.177 10 false +S 2.521,2.604 2.938,2.781 0.417,0.177 10 false G304 2.521,2.76 3.729,2.927 1.208,0.167 10 false Combination Meter

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on GTS and speedometer display are equal.




OK

NG

3.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
3.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
U169571E02
2.458,1.146 2.24,1.594 true 0.073,0.01 0.292,0.208 0.219,0.198 10 false *a 1.521,0.396 1.896,0.573 0.375,0.177 10 false G304 2.135,1.625 2.385,1.802 0.25,0.177 10 false +S

a.

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-17 (+S) - Body ground Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to combination meter assembly)


c.

Reconnect the combination meter assembly connector.



OK

4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
U147515E04
1.083,1.104 0.583,1.927 false 0.125,0.052 0.354,0.281 0.229,0.229 10 false *a 0.25,0.896 0.49,1.063 0.24,0.167 10 false G6 0.385,1.948 0.906,2.135 0.521,0.188 10 false 17 (+S) 2.896,3.542 3.271,3.719 0.375,0.177 10 false GND

a.

Move the shift lever to N.


b.

Jack up the vehicle.


c.

Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-17 (+S) - Body ground Engine switch on (IG) Voltage generated intermittently

Text in Illustration
*a Component with harness connected
(combination meter assembly)


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when a wheel is turned slowly.




OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

REPLACE COMBINATION METER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
G304-17 (+S) - G56-12 (SPD) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
G304-17 (+S) - G55-18 (SPD) Always Below 1 Ω


Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
G304-17 (+S) or G56-12 (SPD) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
G304-17 (+S) or G55-18 (SPD) - Body ground Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR