Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) Vehicle speed is 20 km/h (12.4 mph) or more.

(b) Engine speed is 1000 rpm or more.

(c) STA signal is on.


·

Park/neutral position switch assembly (for automatic transmission models)

·

Clutch start switch assembly (for manual transmission models)

·

Starter (ST) relay circuit

·

Ignition switch

·

ECM



MONITOR STRATEGY

Required Sensors/Components (Main) Starter (ST) relay, Ignition switch assembly, Park/neutral position switch assembly (for automatic transmission models), Clutch start switch assembly (for manual transmission models)
Required Sensors/Components (Related) Vehicle speed sensor, Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Starter signal ON

CONFIRMATION DRIVING PATTERN

A231469E04
1.226,1.979 1.604,2.156 0.378,0.177 10 Idling 0.4,2.252 1.611,2.575 1.211,0.323 10 Ignition Switch ON 0.435,0.813 1.601,1.021 1.166,0.208 10 24 km/h (15 mph) 2.393,2.851 3.076,3.167 0.684,0.316 10 5 seconds or more 3.595,2.938 4.867,3.103 1.272,0.165 10 20 seconds or more 2.004,2.336 2.197,2.525 0.193,0.188 10 [A] 2.586,2.125 2.796,2.297 0.210,0.172 10 [B] 4.03,0.457 4.257,0.625 0.227,0.168 10 [C] 4.905,3.342 5.139,3.510 0.234,0.168 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0617.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A413221E01
0.125,0.052 4.104,0.25 3.979,0.198 10 false w/o Entry and Start System 1.167,0.958 1.625,1.156 0.458,0.198 10 false AM1 0.479,1.094 0.938,1.292 0.458,0.198 10 false ALT 2.146,0.656 2.302,0.854 0.156,0.198 10 false 2 3.167,0.635 3.323,0.833 0.156,0.198 10 false 1 2.344,0.656 2.802,0.854 0.458,0.198 10 false AM1 2.833,0.646 3.292,0.844 0.458,0.198 10 false ST1 2.344,1.323 2.802,1.521 0.458,0.198 10 false AM2 2.833,1.323 3.292,1.521 0.458,0.198 10 false ST2 3.167,1.323 3.323,1.521 0.156,0.198 10 false 8 2.104,1.354 2.26,1.552 0.156,0.198 10 false 7 1.219,1.667 1.531,1.865 0.313,0.198 10 false ST 2.281,1.885 2.594,2.083 0.313,0.198 10 false G2 2.271,2.031 3.219,2.427 0.948,0.396 10 false Ignition Switch Assembly 4.729,0.688 5.042,0.885 0.313,0.198 10 false *1 5.969,1.677 6.281,1.875 0.313,0.198 10 false *1 5.729,4.26 6.042,4.458 0.313,0.198 10 false *1 4.146,1.354 4.458,1.552 0.313,0.198 10 false *2 4.292,3.438 4.906,3.635 0.615,0.198 10 false C159 4.281,3.604 5.302,4.167 1.021,0.563 10 false Park/Neutral Position Switch Assembly*1 3.938,1.792 4.094,1.99 0.156,0.198 10 false 2 3.927,2.438 4.083,2.635 0.156,0.198 10 false 1 4.302,1.771 4.76,1.969 0.458,0.198 10 false A41 4.24,2.01 5.427,2.396 1.188,0.385 10 false Clutch Start Switch Assembly*2 6.417,0.792 6.875,0.99 0.458,0.198 10 false NSW 6.146,0.667 6.458,0.865 0.313,0.198 10 false 15 6.438,5.031 6.896,5.229 0.458,0.198 10 false STA 6.146,4.917 6.458,5.115 0.313,0.198 10 false 17 4.177,4.552 4.49,4.75 0.313,0.198 10 false *2 3.469,4.469 3.625,4.667 0.156,0.198 10 false 5 2.656,4.479 2.813,4.677 0.156,0.198 10 false 3 2.646,4.917 2.802,5.115 0.156,0.198 10 false 1 3.479,4.917 3.635,5.115 0.156,0.198 10 false 2 3.052,5.375 3.365,5.573 0.313,0.198 10 false ST 1.625,5.031 2.24,5.229 0.615,0.198 10 false C158 0.958,5.323 1.271,5.521 0.313,0.198 10 false D4 1.479,5.031 1.635,5.229 0.156,0.198 10 false 1 1.021,5.125 1.177,5.323 0.156,0.198 10 false 1 0.479,3.521 1.552,3.719 1.073,0.198 10 false 250A FL 0.667,6.729 1.74,6.927 1.073,0.198 10 false Battery 1.458,6.135 2.531,6.333 1.073,0.198 10 false Starter 6.469,6.125 7.083,6.323 0.615,0.198 10 false C154 6.5,6.302 6.958,6.5 0.458,0.198 10 false ECM 3.656,6.458 5.667,6.74 2.01,0.281 10 false *1: for Automatic Transmission 3.677,6.885 5.469,7.115 1.792,0.229 10 false *2: for Manual Transmission

A413213E03
0.927,0.844 1.24,1.042 0.313,0.198 10 false NE 0.76,1.531 1.375,1.729 0.615,0.198 10 false STAR 0.854,3.115 1.313,3.313 0.458,0.198 10 false STA 0.25,3.938 0.865,4.135 0.615,0.198 10 false G213 0.25,4.125 2.094,4.51 1.844,0.385 10 false Certification ECU (Smart Key ECU Assembly) 6.083,0.854 6.542,1.052 0.458,0.198 10 false G180 6.188,0.656 6.5,0.854 0.313,0.198 10 false 16 1.271,0.719 1.49,0.938 0.219,0.219 10 false 14 1.25,1.417 1.563,1.615 0.313,0.198 10 false 10 1.271,3.01 1.583,3.208 0.313,0.198 10 false 12 6.104,1.542 6.563,1.74 0.458,0.198 10 false C154 6.208,1.354 6.521,1.552 0.313,0.198 10 false 23 6.458,0.833 6.917,1.031 0.458,0.198 10 false NEO 6.469,1.531 6.927,1.729 0.458,0.198 10 false NSW 5.188,4.625 5.802,4.823 0.615,0.198 10 false C159 5.177,4.823 6.177,5.385 1,0.563 10 false Park/Neutral Position Switch Assembly 4.802,4.531 4.958,4.729 0.156,0.198 10 false 4 4.573,5.354 4.729,5.552 0.156,0.198 10 false 5 1.604,5.115 1.917,5.313 0.313,0.198 10 false ST 0.542,5.646 1.615,5.844 1.073,0.198 10 false 250A FL 3.531,5.823 3.688,6.021 0.156,0.198 10 false 5 2.771,5.813 2.927,6.01 0.156,0.198 10 false 3 2.781,6.229 2.938,6.427 0.156,0.198 10 false 1 3.542,6.25 3.698,6.448 0.156,0.198 10 false 2 3.125,6.698 3.438,6.896 0.313,0.198 10 false ST 6.083,6.354 6.542,6.552 0.458,0.198 10 false C154 6.177,6.146 6.49,6.344 0.313,0.198 10 false 17 6.469,6.354 6.927,6.552 0.458,0.198 10 false STA 6.521,7.438 6.979,7.635 0.458,0.198 10 false ECM 1.688,6.344 2.146,6.542 0.458,0.198 10 false C158 1.031,6.625 1.344,6.823 0.313,0.198 10 false D4 1.083,6.438 1.24,6.635 0.156,0.198 10 false 1 1.552,6.344 1.708,6.542 0.156,0.198 10 false 1 1.469,7.438 2.542,7.635 1.073,0.198 10 false Starter 0.677,8.083 1.75,8.281 1.073,0.198 10 false Battery 0.156,0.031 3.979,0.229 3.823,0.198 10 false w/ Entry and Start System

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON
(for Automatic Transmission Models)
B
ON
(for Manual Transmission Models)
C




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

4.INSPECT CLUTCH START SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.



OK

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (clutch start switch assembly - ST relay - ECM).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Drive the vehicle at more than 24 km/h (15 mph) for more than 20 seconds.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result
Result Proceed to
P0617 is output A
No DTC is output B



A

B

END