1.INSPECT TIRES
Check the tires for wear and proper inflation pressure.
| Tire Size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| P245/70R17 108S | 220 (2.2, 32) | 220 (2.2, 32) |
| 245/70R17 110S | 220 (2.2, 32) | 220 (2.2, 32) |
| P265/65R17 110S | 220 (2.2, 32) | 220 (2.2, 32) |
| 265/65R17 112S | 220 (2.2, 32) | 220 (2.2, 32) |
| 265/55R19 109V | 220 (2.2, 32) | 220 (2.2, 32) |
| Tire Size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| 245/70R17 110S | 200 (2.0, 29) | 200 (2.0, 29) |
| 265/65R17 112S | 200 (2.0, 29) | 200 (2.0, 29) |
| 265/60R18 110H | 200 (2.0, 29) | 200 (2.0, 29) |
| Tire Size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| 245/70R17 110S | 200 (2.0, 29) | 200 (2.0, 29) |
| 265/65R17 112S | 200 (2.0, 29) | 200 (2.0, 29) |
| 265/60R18 110H | 200 (2.0, 29) | 200 (2.0, 29) |
| Tire Size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| 245/70R17 110S | 200 (2.0, 29) | 200 (2.0, 29) |
| 265/65R17 112S | 200 (2.0, 29) | 200 (2.0, 29) |
| 265/60R18 110H | 200 (2.0, 29) | 200 (2.0, 29) |
| Tire Size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
| 245/70R17 110S | 200 (2.0, 29) | 200 (2.0, 29) |
| 265/65R17 112S | 200 (2.0, 29) | 200 (2.0, 29) |
| 265/60R18 110H | 200 (2.0, 29) | 200 (2.0, 29) |
Tire pressure adjustment method when warm:
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Adjust the tire pressure so that the displayed value is equal to the set pressure.
Perform initialization and check that initialization completes.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
Check and record the value of the Data List item "Temperature in Tire". (Ts)
Check and record the ambient temperature during tire pressure adjustment. (Tm)
Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)
Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P
P = (Specified Pressure) + (Ts - Tm)
Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".
Check the tire pressure warning system for the relationship between the inflation pressure and tire pressure warning pressure.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using a dial indicator, check the tire runout.
2.0 mm (0.0787 in.) or less
2.ROTATE TIRES
Rotate the tires as shown in the illustration.
| *a | Front of the Vehicle |
| *b | for Vehicles with Spare Tire |
| *c | for Vehicles without Spare Tire |
3.INSPECT WHEEL BALANCE
for Steel Wheel Type:
Check and adjust the off-the-car balance.
12 g (0.0265 lb.) or less
If necessary, check and adjust the on-the-car balance.
for Aluminum Wheel Type:
Check and adjust the off-the-car balance.
6.0 g (0.0132 lb.) or less
| *a | for 17 Inch Wheels and 19 Inch Wheels | *b | for 18 Inch Wheels |
Using a cleaning detergent, remove dirt, oil and water from the surface where the balance weight is to be adhered.
Do not touch the adhesive surface of the tape.
Attach a sticking type balance weight to the flat surface (A) shown in the illustration.
25 mm (0.984 in.)
Push the balance weight securely with your finger so that it securely adheres to the position.
Do not reuse the balance weight.
For 17 inch wheels, the outer side balance weight should be installed by clipping it to the rim.
If necessary, check and adjust the on-the-car balance.
4.INSPECT FRONT AXLE HUB BEARING LOOSENESS
5.REMOVE FRONT AXLE HUB RUNOUT
6.INSPECT REAR AXLE SHAFT RUNOUT