Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2017.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2111  Transmitter ID1 Operation Stop  C2112  Transmitter ID2 Operation Stop  C2113  Transmitter ID3 Operation Stop  C2114  Transmitter ID4 Operation Stop  C2115  Transmitter ID 5 Operation Stop  


DESCRIPTION

The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates. The tire pressure warning ECU and receiver stores a DTC when the tire pressure warning valve and transmitter stops transmitting signals. The signals can be forcibly transmitted by releasing the tire pressure rapidly. The stored DTCs are cleared when signal transmission resumes.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2111 Transmitter ID1 Operation Stop Tire pressure warning valve and transmitters stop transmitting signals
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2112 Transmitter ID2 Operation Stop Tire pressure warning valve and transmitters stop transmitting signals
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2113 Transmitter ID3 Operation Stop Tire pressure warning valve and transmitters stop transmitting signals
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2114 Transmitter ID4 Operation Stop Tire pressure warning valve and transmitters stop transmitting signals
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2115 Transmitter ID 5 Operation Stop Tire pressure warning valve and transmitters stop transmitting signals
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-

HINT:

It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM

C385511E02
0.417,1.833 1.948,2.156 1.531,0.323 10 false Tire Pressure Warning Valve and Transmitter 3.01,0.302 4.542,0.625 1.531,0.323 10 false Tire Pressure Warning Valve and Transmitter 0.417,0.813 1.948,1.135 1.531,0.323 10 false Tire Pressure Warning Valve and Transmitter 3,1.333 4.531,1.656 1.531,0.323 10 false Tire Pressure Warning Valve and Transmitter 3,2.333 4.531,2.656 1.531,0.323 10 false Tire Pressure Warning Valve and Transmitter* 2.333,5.333 4.833,5.583 2.5,0.25 10 false Tire Pressure Warning Reset Switch 5.75,6.729 7.156,7.135 1.406,0.406 10 false Tire Pressure Warning ECU and Receiver 2.333,5.167 2.833,5.333 0.5,0.167 10 false G153 1.396,3.344 3.146,3.677 1.75,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 1,3.344 1.5,3.51 0.5,0.167 10 false G218 5.75,6.563 6.25,6.729 0.5,0.167 10 false R41 5.958,3.427 6.417,3.625 0.458,0.198 10 false RDA 3.198,3.427 3.656,3.625 0.458,0.198 10 false RDA 3.198,3.885 3.656,4.083 0.458,0.198 10 false PRG 5.958,3.885 6.417,4.083 0.458,0.198 10 false PRG 3.625,3.333 3.781,3.531 0.156,0.198 10 false 4 5.781,3.333 5.938,3.531 0.156,0.198 10 false 4 3.635,3.781 3.792,3.979 0.156,0.198 10 false 5 5.781,3.781 5.938,3.979 0.156,0.198 10 false 5 5.958,4.865 6.417,5.063 0.458,0.198 10 false CLSW 5.948,6.104 6.406,6.302 0.458,0.198 10 false GND 5.698,5.99 6.01,6.188 0.313,0.198 10 false 12 5.781,4.74 5.938,4.938 0.156,0.198 10 false 3 2.792,4.74 2.948,4.938 0.156,0.198 10 false 2 3.906,4.75 4.063,4.948 0.156,0.198 10 false 1 0.5,7.083 2.49,7.281 1.99,0.198 10 false : Radio Waves 0.448,7.406 2.896,7.604 2.448,0.198 10 false *: w/ Spare Tire

PROCEDURE

1.PERFORM FORCED TRANSMISSION OF TRANSMITTER ID OF ALL WHEELS
a.

Set the tire pressure to the specified value.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*

·

w/ Spare Tire



HINT:
·

*: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121 to C2124 (C2121 to C2125: w/ Spare Tire).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121

·

The wheel position cannot be determined from ID1 through ID4 or ID1 through ID5 (w/ Spare Tire) on the Data List.




h.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

i.

Check that each "ID Tire Inflation Pressure" value displayed on the GTS has changed.

OK:

Each "ID Tire Inflation Pressure" value displayed on the GTS changed to the actual tire inflation pressure value.


NOTICE:
·

It may take a few minutes until the values are displayed.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.




ii.

After confirming that all of the tire "ID Tire Inflation Pressure" values displayed on the GTS have changed, set the tire pressure to the appropriate specified values.

HINT:

If an "ID Tire Inflation Pressure" value displayed on the GTS has not changed after rechecking, inspect for another problem.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121




Result:
Proceed to
OK
NG



OK

END

NG

GO TO TRANSMITTER AND RECEIVER INSPECTION PROCEDURE