Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects in front of the vehicle to the driving support ECU assembly. The driving support ECU assembly sends this information to the hybrid vehicle control ECU assembly and the hybrid vehicle control ECU assembly operates the dynamic radar cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for approximately 1 second or more.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector


U1104 Lost Communication with Driving Support ECU While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approximately 1 second or more.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

C386698E01
1.896,2.625 4.313,2.875 2.417,0.25 10 false Forward Recognition Camera 5.313,4.635 5.927,4.833 0.615,0.198 10 false G224 1.906,2.458 2.521,2.656 0.615,0.198 10 false W22 1.958,4.635 2.573,4.833 0.615,0.198 10 false A100 2.927,1.729 3.542,1.927 0.615,0.198 10 false CANL 2.917,2.021 3.531,2.219 0.615,0.198 10 false CANH 2.5,1.99 3.115,2.188 0.615,0.198 10 false GND 2.51,1.458 3.125,1.656 0.615,0.198 10 false IGB 2.531,3.906 3.146,4.104 0.615,0.198 10 false SGND 2.531,3.323 3.146,3.521 0.615,0.198 10 false IGB 5.5,0.458 6.115,0.656 0.615,0.198 10 false B 2.906,3.542 3.521,3.74 0.615,0.198 10 false CA1P 2.938,4.073 3.552,4.271 0.615,0.198 10 false CA1N 5.49,3.583 6.104,3.781 0.615,0.198 10 false CA1P 5.49,4.073 6.104,4.271 0.615,0.198 10 false CA1N 5.99,3.969 6.604,4.167 0.615,0.198 10 false GND 1.948,4.813 4.854,5.094 2.906,0.281 10 false Millimeter Wave Radar Sensor Assembly 1.083,5.313 4.75,5.51 3.667,0.198 10 false : CAN Communication Line 1.594,0.615 3.281,0.813 1.688,0.198 10 false ECU-IG NO.1 0.26,0.458 1.417,0.698 1.156,0.24 10 false from IG Circuit 3.385,1.594 3.698,1.792 0.313,0.198 10 false 12 3.417,1.885 3.729,2.083 0.313,0.198 10 false 6 2.313,1.354 2.625,1.552 0.313,0.198 10 false 7 2.25,1.875 2.563,2.073 0.313,0.198 10 false 10 2.333,3.198 2.646,3.396 0.313,0.198 10 false 8 2.333,3.781 2.646,3.979 0.313,0.198 10 false 1 3.406,3.927 3.719,4.125 0.313,0.198 10 false 6 5.292,3.427 5.604,3.625 0.313,0.198 10 false 8 5.292,3.906 5.604,4.104 0.313,0.198 10 false 9 5.313,0.344 5.625,0.542 0.313,0.198 10 false 7 6.385,3.854 6.698,4.052 0.313,0.198 10 false 28 3.396,3.427 3.708,3.625 0.313,0.198 10 false 5 5.313,4.802 6.594,5.219 1.281,0.417 10 false Driving Support ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output OK
CAN communication system DTCs are output NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
A380143C78
1.583,0.198 2,0.417 0.417,0.219 1.26,0.958 0.896,0.354 true 2.281,1.813 2.479,1.281 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.625,0.229 2.083,0.427 0.458,0.198 10 false G224 0.781,0.25 0.938,0.448 0.156,0.198 10 false B 1.958,1.74 2.344,1.948 0.385,0.208 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-28 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G224-7 (B) - Body ground Ignition switch ON 10.5 to 16 V
G224-7 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
A380144C58
1.458,0.156 1.906,0.396 0.448,0.24 0.885,0.792 1.406,1.052 true 1.969,1.198 2.573,1.5 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.531,0.198 2.281,0.448 0.75,0.25 10 false A100 0.458,0.708 1.073,0.906 0.615,0.198 10 false SGND 2.625,1.438 3.031,1.646 0.406,0.208 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A100 millimeter wave radar sensor assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-1 (SGND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
A100-8 (IGB) - Body ground Ignition switch ON 10.5 to 16 V
A100-8 (IGB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the G224 driving support ECU assembly connector.


b.

Disconnect the A100 millimeter wave radar sensor assembly connector.


c.

Disconnect the W22 forward recognition camera connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-8 (CA1P) - A100-5 (CA1P) Always Below 1 Ω
G224-9 (CA1N) - A100-6 (CA1N) Always Below 1 Ω
G224-8 (CA1P) or A100-5 (CA1P) - Body ground Always 10 kΩ or higher
G224-9 (CA1N) or A100-6 (CA1N) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs
6.CHECK FOR DTCs
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.



d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U0235 and U1104 are not output A
DTC U0235 or U1104 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY