The skid control ECU (brake actuator assembly) receives signals from the acceleration sensor (airbag sensor assembly) via the CAN communication system.
The airbag sensor assembly has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there is trouble in the bus lines between the acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123 (malfunction in CAN communication with the yaw rate sensor) and U0124 (malfunction in CAN communication with the acceleration sensor) are stored.
These DTCs are also stored when calibration has not been completed.
DTC C1279 can be cleared when the acceleration sensor (airbag sensor assembly) sends an acceleration signal or test mode ends. DTC C1279 is stored only in test mode.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1243 | While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change by 0.0294 G or more occurs 16 times or more. | ·
IGN fuse ·
Acceleration sensor (Airbag sensor assembly) ·
Acceleration sensor (Airbag sensor assembly) circuit |
| C1245 | At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more. | ·
IGN fuse ·
Acceleration sensor (Airbag sensor assembly) ·
Acceleration sensor (Airbag sensor assembly) circuit ·
Sensor installation |
| C1279 | Stored only during test mode. | ·
Acceleration sensor (Airbag sensor assembly) ·
Sensor installation |
When replacing the acceleration sensor (airbag sensor assembly) , perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When DTC U0124 is output together with DTC C1243 and/or C1245, inspect and repair the trouble areas indicated by DTC U0124 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>U0073).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel and decelerate (depress the brake pedal) the vehicle.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC output (relating to yaw rate and acceleration sensor) | A |
| DTC output (relating to CAN communication system) | B |
A
B
Turn the ignition switch off.
Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).
The sensor is tightened to the specified torque.
The sensor is not tilted.
OK
NG
(See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION)
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the G1 acceleration sensor (airbag sensor assembly) connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G1-21 (IG2) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-25 (E1) - Body ground | Always | Below 1 Ω |
| G1-26 (E2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Acceleration Sensor (Airbag Sensor Assembly)) |
| Result | Proceed to |
|---|---|
| OK (When troubleshooting in accordance with diagnostic trouble code chart) | A |
| OK (When troubleshooting in accordance with problem symptoms table) | B |
| NG | C |
Check the acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).
A
B
(See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE)
C