The forward recognition camera uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.
When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the yaw rate sensor (airbag sensor assembly) etc., the millimeter wave radar sensor assembly performs self diagnosis to check if the sensor beam axis has deviated from the vehicle movement direction. When the millimeter wave radar sensor assembly beam axis has deviated, the forward recognition camera detects this, and stores DTC C1A11.
After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A11 | Front Radar Sensor Incorrect Axial Gap | 2 seconds after the ignition switch is turned ON, misalignment of the millimeter wave radar sensor assembly is detected for approximately 5 seconds. | ·
Millimeter wave radar sensor assembly ·
Forward recognition camera |
| C1A14 | Front Radar Sensor Beam Axis Not Adjusted | 2 seconds after the ignition switch is turned ON, incompletion of the millimeter wave radar sensor beam axis alignment is detected for approximately 5 seconds. | ·
Millimeter wave radar sensor assembly ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If amillimeter wave radar sensor assembly which was installed to another vehicle is used, theinformation stored in the millimeter wave radar sensor assembly will not match the informationfrom the vehicle. As a result, a DTC may be stored.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Current DTC C1A11 is output | A |
| Current DTC C1A14 is output | B |
| History DTC C1A11 is output | C |
A
B
C
Check the operating conditions of the vehicle.
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.
| Result | Proceed to |
|---|---|
| Vehicle is not overloaded or being towed. | A |
| Vehicle is overloaded or being towed. | B |
A
B
Check the front wheel alignment (toe).
Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).
| Result | Proceed to |
|---|---|
| Front wheel is misaligned (toe) | A |
| Front wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels.
Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the forward recognition camera.
| Result | Proceed to |
|---|---|
| DTC C1A11 is not output | A |
| DTC C1A11 is output | B |
A
B
Check that the bracket of the millimeter wave radar sensor assembly is not deformed.
When the bracket is deformed, replace the millimeter wave radar sensor assembly.
The bracket is not deformed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Return the vehicle to normal operating conditions.
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A11 is not output | A |
| DTC C1A11 is output | B |
A
B
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the forward recognition camera.
| Result | Proceed to |
|---|---|
| DTC C1A14 is not output | A |
| DTC C1A14 is output | B |
A
B
Check for DTCs related to misalignment of millimeter wave radar sensor assembly.
If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT