Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0332058 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  


DESCRIPTION

The forward recognition camera receives vehicle stability signals from the yaw rate sensor (airbag sensor assembly). If the yaw rate sensor (airbag sensor assembly) detects an abnormal yaw rate sensor signal or yaw rate sensor (airbag sensor assembly) power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA4 Yaw Rate Sensor Circuit While the vehicle speed is 1 km/h (1 mph) or more, the lane departure alert system is operating and a signal from the yaw rate sensor indicating a malfunction in the yaw rate sensor (airbag sensor assembly) is detected by the forward recognition camera for 5 seconds or more.
·

Vehicle stability control system

·

Yaw rate sensor (airbag sensor assembly)

·

Forward recognition camera


C1AA5 Yaw Rate Sensor Power Supply Voltage Circuit While the vehicle speed is 1 km/h (1 mph) or more, the lane departure alert system is operating and a signal from the yaw rate sensor (airbag sensor assembly) indicating an abnormal yaw rate sensor power supply voltage signal is detected by the forward recognition camera for 5 seconds or more.
·

Vehicle stability control system

·

Yaw rate sensor (airbag sensor assembly)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

for 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR

except 2TR-FE: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR

HINT:

Lane departure alert system DTC C1AA4 or C1AA5 may be stored due to a malfunction in the vehicle stability control system. Therefore it is necessary to check for and troubleshoot vehicle stability control system DTCs first.



Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

B

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AA4 and C1AA5 are not output. A
DTC C1AA4 or C1AA5 is output. B



A

B

3.REPLACE FORWARD RECOGNITION CAMERA
3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AA4 and C1AA5 are not output. A
DTC C1AA4 or C1AA5 is output. B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE YAW RATE SENSOR (AIRBAG SENSOR ASSEMBLY)