Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0332059 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AAE  Heater Circuit  


DESCRIPTION

The forward recognition camera controls the flow of current to the forward recognition with heater hood sub-assembly.

If the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAE Heater Circuit
Either of the following conditions is met after 2 seconds have elapsed since the ignition switch was turned ON:
·

Short to +B detected in the forward recognition with heater hood sub-assembly circuit for 1 second or more cumulatively

·

Open or short to ground detected in the forward recognition with heater hood sub-assembly circuit for 5 seconds or more


·

Forward recognition with heater hood sub-assembly

·

Forward recognition camera

·

Harness or connector



WIRING DIAGRAM

C368913E21
4.917,1.938 5.229,2.135 0.313,0.198 10 false W22 4.927,2.094 6.854,2.302 1.927,0.208 10 false Forward Recognition Camera 5.542,0.708 6,0.906 0.458,0.198 10 false HTR 5.333,0.552 5.792,0.75 0.458,0.198 10 false 1 3.188,1.021 5.052,1.427 1.865,0.406 10 false Forward Recognition with Heater Hood Sub-assembly 2.094,0.844 3.469,1.042 1.375,0.198 10 false ECU-IG NO. 1 0.531,0.698 2.823,0.896 2.292,0.198 10 false from IG Circuit 3.604,0.698 4.063,0.896 0.458,0.198 10 false IG1 4.125,0.698 4.583,0.896 0.458,0.198 10 false HTR 3.375,0.573 3.833,0.771 0.458,0.198 10 false 1 4.521,0.573 4.979,0.771 0.458,0.198 10 false 2 3.177,0.875 4.552,1.073 1.375,0.198 10 false W23 5.26,1.49 5.719,1.688 0.458,0.198 10 false 10 5.531,1.625 5.99,1.823 0.458,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AAE is not output A
DTC C1AAE is output B



A

B

2.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
2.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
a.

Turn the ignition switch off.


b.
A401973C21
1.688,1.854 1.823,1.26 true 2.188,1.854 2.042,1.271 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.563,1.885 2.021,2.083 0.458,0.198 10 false HTR 2.135,1.885 2.594,2.083 0.458,0.198 10 false IG1
*a Component without harness connected
(Forward Recognition with Heater Hood Sub-assembly)


Disconnect the W23 forward recognition with heater hood sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W23-1 (IG1) - W23-2 (HTR) Ignition switch off 38 to 42 Ω



d.

Connect the W23 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE VOLTAGE)

NG

REPLACE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE VOLTAGE)
a.
A401974C26
1.552,0.208 1.938,0.448 0.385,0.24 1.125,1.125 1.552,1.219 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.604,0.25 2.063,0.448 0.458,0.198 10 false W23 0.854,1.042 1.135,1.198 0.281,0.156 10 false IG1
*a Front view of wire harness connector
(to Forward Recognition with Heater Hood Sub-assembly)


Disconnect the W23 forward recognition with heater hood sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W23-1 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1.5 V



c.

Connect the W23 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the W23 forward recognition with heater hood sub-assembly connector.


b.

Disconnect the W22 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W23-2 (HTR) - W22-1 (HTR) Always Below 1 Ω
W23-2 (HTR) or W22-1 (HTR) - Body ground Always 10 kΩ or higher



d.

Connect the W22 forward recognition camera connector.


e.

Connect the W23 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.

Disconnect the W22 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the W22 forward recognition camera connector


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR