Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › 2017.08–2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0705 One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
·

One of the following conditions is met.

-

P input signal is ON

-

N input signal is ON

-

NSW input signal is ON


·

R input signal

·

D input signal


(B) Any of the following signals is ON for 2.0 seconds or more with the shift lever in S (2 trip detection logic):
·

P input signal

·

N input signal

·

NSW input signal

·

R input signal


(C) All signals are OFF simultaneously for NSW, P, R, N and D (2 trip detection logic).
·

Open or short in park/neutral position switch assembly circuit

·

Transmission control switch (transmission floor shift assembly)

·

Park/neutral position switch assembly

·

ECM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C330136E14
5.969,0.646 6.427,0.854 0.458,0.208 10 false 12 V 4.833,0.938 5.292,1.146 0.458,0.208 10 false G184 4.938,0.74 5.396,0.948 0.458,0.208 10 false 11 5.292,0.833 5.75,1.042 0.458,0.208 10 false NSW 3.76,0.823 4.219,1.031 0.458,0.208 10 false 4 3.51,0.823 3.969,1.031 0.458,0.208 10 false B 2.74,0.823 3.198,1.031 0.458,0.208 10 false L 2.542,0.823 3,1.031 0.458,0.208 10 false 5 2.729,2.167 3.188,2.375 0.458,0.208 10 false RB 2.542,2.167 3,2.375 0.458,0.208 10 false 2 5.292,1.281 5.75,1.49 0.458,0.208 10 false P 3.76,1.25 4.219,1.458 0.458,0.208 10 false 6 3.448,1.26 3.906,1.469 0.458,0.208 10 false PL 5.292,1.885 5.75,2.094 0.458,0.208 10 false R 3.76,1.865 4.219,2.073 0.458,0.208 10 false 1 3.448,1.865 3.906,2.073 0.458,0.208 10 false RL 5.292,2.479 5.75,2.688 0.458,0.208 10 false N 3.76,2.458 4.219,2.667 0.458,0.208 10 false 9 3.458,2.469 3.917,2.677 0.458,0.208 10 false NL 5.292,3.083 5.75,3.292 0.458,0.208 10 false D 3.76,3.063 4.219,3.271 0.458,0.208 10 false 7 3.438,3.063 3.896,3.271 0.458,0.208 10 false DL 1.927,3.625 2.385,3.833 0.458,0.208 10 false C159 1.927,3.823 4.594,4.031 2.667,0.208 10 false Park/Neutral Position Switch Assembly 0.927,0.906 1.938,1.115 1.01,0.208 10 false to ST Relay 0.094,2.271 1.865,2.49 1.771,0.219 10 false from ECU-IG NO. 1 Fuse 0.083,4.76 1.854,4.969 1.771,0.208 10 false from ECU-IG NO. 1 Fuse 2.208,5.219 2.667,5.427 0.458,0.208 10 false G47 2.208,5.406 4.448,5.615 2.24,0.208 10 false Transmission Control Switch 5.292,4.667 5.75,4.875 0.458,0.208 10 false S 3.75,4.677 4.208,4.885 0.458,0.208 10 false 7 3.521,4.667 3.979,4.875 0.458,0.208 10 false S 2.74,4.667 3.198,4.875 0.458,0.208 10 false IG 2.542,4.677 3,4.885 0.458,0.208 10 false 3 4.938,1.198 5.396,1.406 0.458,0.208 10 false 12 4.938,1.781 5.396,1.99 0.458,0.208 10 false 15 4.938,2.385 5.396,2.594 0.458,0.208 10 false 13 4.938,3 5.396,3.208 0.458,0.208 10 false 14 4.938,4.594 5.396,4.802 0.458,0.208 10 false 13 5.677,6.073 6.51,6.281 0.833,0.208 10 false ECM 4.844,1.375 5.302,1.583 0.458,0.208 10 false C149 4.833,1.969 5.292,2.177 0.458,0.208 10 false C149 4.833,2.573 5.292,2.781 0.458,0.208 10 false C149 4.833,3.188 5.292,3.396 0.458,0.208 10 false C149 4.833,4.771 5.292,4.979 0.458,0.208 10 false G184

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>PRECAUTION).



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the engine switch on (IG).*1

2.

Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more.*2

3.

Wait for 2 seconds or more with the shift lever in S.*3

4.

Turn the engine switch off.

5.

Perform steps (*1) through (*3) again.



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in D, S, "+" or "-"

·

OFF: Shift lever not in D, S, "+" or "-"


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
U170316E02
1.771,1 2.031,0.344 false 0.125,0.094 0.344,0.333 0.219,0.24 10 false *a 0.49,1.021 0.896,1.198 0.406,0.177 10 false C159 2.073,0.24 2.313,0.427 0.24,0.188 10 false RB

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V
C159-2 (RB) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
U170317E02
2.073,1 2.292,0.188 false 0.115,0.094 0.333,0.333 0.219,0.24 10 false *a 0.5,1.021 0.854,1.198 0.354,0.177 10 false C159 2.365,0.104 2.604,0.292 0.24,0.188 10 false B

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-4 (B) - Body ground Engine switch on (IG) 11 to 14 V
C159-4 (B) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712E92
1.865,0.979 2.219,0.365 false 1.281,0.938 0.917,0.365 false 2.094,1.292 2.458,1.781 false 0.99,1.781 1.313,1.292 false 1.583,0.948 1.521,0.365 false 2.052,1.802 1.958,1.292 false 1.635,1.781 1.729,1.281 false 2.26,0.25 2.573,0.448 0.313,0.198 10 false RL 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.76,0.25 1.073,0.448 0.313,0.198 10 false B 2.5,1.677 2.813,1.875 0.313,0.198 10 false L 0.729,1.677 1.042,1.875 0.313,0.198 10 false NL 1.25,0.25 1.563,0.448 0.313,0.198 10 false RB 2.094,1.677 2.406,1.875 0.313,0.198 10 false PL 1.375,1.677 1.688,1.875 0.313,0.198 10 false DL

Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P or N Below 1 Ω
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
2 (RB) - 7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
4 (B) - 5 (L) Shift lever not in P or N 10 kΩ or higher
2 (RB) - 6 (PL) Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever not in D, S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
U148280E03
1.813,1.052 2.344,0.635 false 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a 2.385,0.521 2.698,0.719 0.313,0.198 10 false IG 0.542,1.01 0.917,1.24 0.375,0.229 10 false G47

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G47-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G47-3 (IG) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

5.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
C203344E40
1.615,0.729 1.104,0.323 false 1.115,1.396 1.646,1 false 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 0.896,0.219 1.135,0.417 0.24,0.198 10 false IG 0.958,1.354 1.146,1.552 0.188,0.198 10 false S

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)
a.
U170438E02
0.427,1.896 0.24,2.729 false 0.5,1.906 0.802,2.958 false 0.573,1.885 1.313,2.729 false 0.635,1.896 1.458,2.167 false 2.292,1.896 2.198,2.729 false 0.115,0.073 0.625,0.281 0.51,0.208 10 false *a 0.448,0.25 0.958,0.458 0.51,0.208 10 false C149 0.042,2.781 0.552,2.99 0.51,0.208 10 false 15 (R) 2.26,0.25 2.771,0.458 0.51,0.208 10 false G184 0.583,3.01 1.094,3.219 0.51,0.208 10 false 14 (D) 1.104,2.781 1.615,2.99 0.51,0.208 10 false 13 (N) 1.333,2.219 1.844,2.427 0.51,0.208 10 false 12 (P) 1.958,2.781 2.469,2.99 0.51,0.208 10 false 13 (S)

Disconnect the ECM connectors.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C149-12 (P) - Body ground
·

Engine switch on (IG)

·

Shift lever in P


11 to 14 V
C149-15 (R) - Body ground
·

Engine switch on (IG)

·

Shift lever in R


11 to 14 V*
C149-13 (N) - Body ground
·

Engine switch on (IG)

·

Shift lever in N


11 to 14 V
C149-14 (D) - Body ground
·

Engine switch on (IG)

·

Shift lever in D, S, "+" or "-"


11 to 14 V
G184-13 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever in S, "+" or "-"


11 to 14 V
C149-12 (P) - Body ground
·

Engine switch on (IG)

·

Shift lever not in P


Below 1 V
C149-15 (R) - Body ground
·

Engine switch on (IG)

·

Shift lever not in R


Below 1 V
C149-13 (N) - Body ground
·

Engine switch on (IG)

·

Shift lever not in N


Below 1 V
C149-14 (D) - Body ground
·

Engine switch on (IG)

·

Shift lever not in D, S, "+" or "-"


Below 1 V
G184-13 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever not in S, "+" or "-"


Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to ECM)

HINT:

*: The voltage will drop slightly due to lighting up of the backup light.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the C159 park/neutral position switch assembly connector.


b.

Disconnect the G184 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-4 (B) - G184-11 (NSW) Always Below 1 Ω
C159-4 (B) - Body ground Always 10 kΩ or higher
G184-11 (NSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR