Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) D

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR SYSTEM DIAGNOSTIC MODE


a.

In diagnostic mode for the parking assist monitor system, signals received by the navigation receiver assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the navigation receiver assembly.

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION


HINT:

The displayed items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION)


E323985E01
0.074,0 1.418,0.278 1.344,0.278 12 Example:

E326734


DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION)


E326735E01
0.057,0 1.417,0.253 1.360,0.253 12 Example:

E326733


VEHICLE SIGNAL CHECK


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



b.
E273700

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/ Setting I" screen.


c.
E288888

Select "Vehicle Signal" on the "Function Check/ Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

i.

When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".

See pageAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Navigation Receiver Type)>DTC CHECK / CLEAR

HINT:
·

Only conditions having inputs are displayed.

·

This screen displays vehicle signals input to the navigation receiver assembly.







CAR SIGNAL CHECK (PARKING ASSIST MONITOR SYSTEM INPUT SIGNALS)


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


a.

Start diagnostic mode.

See pageAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Navigation Receiver Type)>DTC CHECK / CLEAR

i.
E273700

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/ Setting I" screen.


ii.
E288889

Select "Camera Setting" on the "Function Check/Setting I" screen.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the rear television camera assembly was replaced.


Parking Assist Monitor System Initialization Screen Transition
Not performed Car Signal Check screen
Performed Mode Setting screen


iii.
E286098

When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Car Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.
E286093

Car Signal Check

i.

On the "Car Signal Check" screen, it is possible to inspect the state of signals and check the settings.

Item Inspection Detail Note
CAN CAN communication signal input When "CHK" (red) is displayed, selecting "Next" will not change the screen to the next screen.

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>DTC CHECK / CLEAR).





CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION).